• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

BEGGING FOR HELP!!

  • Thread starter Thread starter 600hpgt
  • Start date Start date Feb 25, 2007
6

600hpgt

New Member
Feb 9, 2007
9
0
0
proctorville, ohio
Feb 25, 2007
#1
  • Feb 25, 2007
  • #1
Guys i realy need your help here. i have a 302 with HIGH flow ported aftermarket aluminum heads, 1.6 shaft mount roller rockers, high 400 low 500 lift cam, edelbrock dual plane air gap intake, long tube headers, off road h-pipe, 2 1/2 inch cat back with 2 chambers, msd 6al ignition, msd billet distributor with blaster 2 coil and a holly blue pump. i plan on taking the motor to around 6500 or so before shifting. With that all being said, do you guys think i can run a 750 cfm carb., if not what size do you recommend? I don't care about gas mileage at all and the car is not going to be a "daily" driver but will be driven a good bit. Also i don't mind a little tweaking here and there but what brand do you recommend for out of the box and go performance? Any and ALL help is greatly appreciated.....thanks a ton
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Feb 25, 2007
#2
  • Feb 25, 2007
  • #2
I had close to the same setup on my old car, and I ran a holley 750 double pumper.
 

blackened88lx

Active Member
Aug 9, 2006
0
4
28
Connecticut
Feb 25, 2007
#3
  • Feb 25, 2007
  • #3
Doesn't sound like it will see anywhere near 6500 with that small of a cam dual plane intake, etc. What exactly are the heads and cam? This isn't what you're claiming 600hp from is it??
 
6

600hpgt

New Member
Feb 9, 2007
9
0
0
proctorville, ohio
Feb 25, 2007
#4
  • Feb 25, 2007
  • #4
blackened88lx said:
Doesn't sound like it will see anywhere near 6500 with that small of a cam dual plane intake, etc. What exactly are the heads and cam? This isn't what you're claiming 600hp from is it??
Click to expand...

actualy it is except i just converted from efi with 13 lbs of boost blowing through it.
 
6

600hpgt

New Member
Feb 9, 2007
9
0
0
proctorville, ohio
Feb 25, 2007
#5
  • Feb 25, 2007
  • #5
marine_2003 said:
I had close to the same setup on my old car, and I ran a holley 750 double pumper.
Click to expand...

i'm assuming it ran ok?
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Feb 25, 2007
#6
  • Feb 25, 2007
  • #6
Not one problem.
 
You must log in or register to reply here.

Similar threads

1
Electrical Headlight harness trouble
  • 1985fox
  • Apr 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
486
Fox 5.0 Mustang Tech Apr 17, 2026
AeroCoupe
S
Preparation for Holley Terminator X install – Foxbody 306 (electrical fan, alternator, MSD Ignition, etc)
  • So_Flo
  • Mar 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
22
Views
3K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 4, 2026
General karthief
5
Hello Everyone !
  • 5150K
  • Jul 3, 2026
  • The Welcome Wagon
Replies
0
Views
189
The Welcome Wagon Jul 3, 2026
5150K
5
M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
865
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
D
Fuel 1985 GT Fuel Line Diagram
  • DienstXIV
  • Apr 17, 2025
  • Fox 5.0 Mustang Tech
Replies
8
Views
2K
Fox 5.0 Mustang Tech Jul 12, 2025
DienstXIV
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?