• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Best Radiator/cooling setup?

  • Thread starter Thread starter Keith4452
  • Start date Start date Apr 25, 2006
K

Keith4452

New Member
Mar 6, 2006
14
0
0
Apr 25, 2006
#1
  • Apr 25, 2006
  • #1
I'm fed up with my stang seemings how I just bought it and have run into multiple problems-running hot, no blinkers, etc... So I am tearing it down and replacing everything since I have the money for once..lol. The car is a 90 GT and has everything stock, but the 3 inch pipes running to the back dumping out on trick flow exhaust. I have a leak at the upper radiator opening and would like to replace it with a recommended aluminum radiator/fan and setup. I frequently use ebay so any related items are appreciated! I am about to throw a bunch of money to an engine builder to have a less mileage 302 put in and a great cooling system would help! Thanks for the info!
 
8

87'GTstang

New Member
Feb 16, 2004
1,025
0
0
Apr 26, 2006
#2
  • Apr 26, 2006
  • #2
The $190 Griffin radiator from summit (31" x 19") Is by far the best bang for the buck, it performs and looks more expensive than what you pay for it.

Fans can be cheap as hell, the Taurus/sable 3.8L fans are great ($10-20 at the j/y). Also the lincoln mark 7 fans are beasts pulling a lot of air, but it is not as easy to fit in the engine compartment.

Water pumps can sometimes be over-rated. Hands down Stewert and edelbrock I have seen to be the best in terms of severity tests. A standard Ford Racing pump is what I have and it works just fine ($50).

Thermostats, get a good one; 180 works best, 160 is too cold and cuases some issues. Mr. Gasket has good reviews for making a quality one ($10).

Had the setup for a while and any normal driving involved no fan running and any sitting still for a few minutes and the high-speed on the fan brought the temp back down quickly (I use low speed to maintain the temp if needed).
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Apr 26, 2006
#3
  • Apr 26, 2006
  • #3
Well, for a completely stock mustang except exhaust, the only thing I would do is swap to the taurus fan (or some electric fan) with a DCC controller. If the stock radiator could keep mine cool in the ambient temps here in AZ summers, it'll surely be fine for you.

I used to run a 180 t-stat too in my '88, just for the heck of it.. never noticed much of a difference. Never had any cooling problems.
 
K

Keith4452

New Member
Mar 6, 2006
14
0
0
Apr 26, 2006
#4
  • Apr 26, 2006
  • #4
radiator

I would run my stock radiator if it didn't have a hole in the upper lip where the hose goes in. Plus I am swaping this motor out this summer with a built 302 that will prob need a good cooling system. Third...I want it to look nice and new seemings how i'm redoing the whole car. I like the sounds of the summit radiator looking nice and being cheaper, but does it bolt right up without buying any extra adapters? I forgot to say that I busted a bolt on the water pump and will have to coil it out will prob be a pain where it is in the car.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Apr 26, 2006
#5
  • Apr 26, 2006
  • #5
I am using a stock 302 2-core radiator from the local parts store. Probably the least expensive option, and it keeps up with the 408w very well. The highest ECT temp I have seen in a datalog is 198F, using a 197F Prestone Stat (I don't recommend Prestone, as it seems to stick open).

The stock 2-core will work just fine, or jump up to the 3-core (ask for a 93 cobra rad).

jason
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Apr 26, 2006
#6
  • Apr 26, 2006
  • #6
i've got a cheapy Brass 3 core radiator that is thicker than stock and cools so much better than the stocker.
 

vikingpower

New Member
Dec 6, 2004
656
0
0
CWU Ellensburg, WA
Apr 26, 2006
#7
  • Apr 26, 2006
  • #7
I use the big Summit alum. radiator, summit water pump, 195 tstat, and no fan whatsoever. Sometimes gets a little warm if I sit in traffic, otherwise it runs very cool
 

ras50gt

Member
Oct 25, 2005
200
2
19
Apr 26, 2006
#8
  • Apr 26, 2006
  • #8
I went with the aluminum summit one. I would recommend the summit or griffin. I bought the summit 31" L X 19" H: part number SUM-380431. I couldn't be happier with how well it keeps temps low especially compared to the stock one. The only issue I had was the fitment, it fits in there tight (had to bend some metal lines on the passenger side but nothing serious) and because its almost 3 inches wide, the fan shroud (assuming you still have the stock one) will move closer to the fan belt. I ended up cutting the stock shroud when I had to get to the belt tensioner. So, I would recommend going one size smaller, summit makes a 27 3/8" L X 19" H part number SUM-380428. I think this may have made the install a lot easier. The other issue you will have is connecting the hoses. The inlet and outlet of the summit ones are bigger than the stock ones; I used some Vaseline to help get them on. I also cut about two inches off the bottom hose; u will notice that the hose will bend slightly due to the bottom inlet slanting up-word as well as the radiator being wider than the stock one. You will need to get a fitting to go into the radiator neck that connects to the overflow tank hose. I got this from pep boys. Also, you will have to drill holes for the shroud to hook up at the top, I used the stock shroud screws. Then drilled holes for the shroud at the bottom of the radiator; I used zip ties to hold it together at the bottom. The only other suggestion I have is to consider installing an electric fan while doing the new radiator; if you do it later, it will mean more work later on. The only thing is without the stock fan shroud, you will have to figure out a way to mount the stock over flow tank or buy an aftermarket one and mount that some how. Also, there is no drain plug on the radiator, I decided I wasnt going to spend another 100+ for a more expensive radiator with one. I don't think the griffin or jegs have them either.


Another thing to think about when deciding on the summit or griffin, is to look at the construction. The summit is fully welded while the griffin uses an epoxy seal. Most people I talked to told me to get a welded radiator. I did a little research on epoxy ones, but i'm still not too sure how they compare. During my install, I first thought I should have spent the extra money on an actual direct fit mustang radiator, but as soon as it was in I was glad I went with the summit one. Plus I was going to buy an electric fan with the money I saved but never got to it.


I know this was long, but you should have no problems with your install and it should save you some money, which is always good. Like most things, its better to do it right the first time. I learned a lot from my experience and I hope all this helps.
 
K

Keith4452

New Member
Mar 6, 2006
14
0
0
Apr 27, 2006
#9
  • Apr 27, 2006
  • #9
Thanks for the advice! I usually learn the hard way as well so this should help. I would like to find a perfect fit application, but if it means better cooling I will do the work to make another fit.
 

1988WHTGT

Member
Mar 31, 2005
270
0
17
Guyton, GA
Apr 27, 2006
#10
  • Apr 27, 2006
  • #10
People keep telling me to go this route...
http://cgi.ebay.com/ebaymotors/80-9...33602QQitemZ8049969782QQrdZ1QQsspagenameZWD1V
 
You must log in or register to reply here.

Similar threads

S
Fuel ‘88 GT Runs Rich Cold — Fixes Itself When I Unplug Sensors (ECT, MAF, O2, etc.)
  • Sufarry
  • Nov 6, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
1K
Fox 5.0 Mustang Tech Nov 9, 2025
Mustang5L5
B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
469
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
618
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
F
Ford 460 swap
  • Ford460
  • Sep 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
502
1996 - 2004 SN95 Mustang -General/Talk- Sep 14, 2026
Ford460
F
Progress Thread Progress Thread- From6to8's 95 GT/Saleen Supercharged 331 install
  • from6to8
  • Mar 22, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
27
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 28, 2026
from6to8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?