• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Brake lights not working??

  • Thread starter Thread starter epurdy2005
  • Start date Start date Apr 27, 2008
E

epurdy2005

New Member
Apr 3, 2004
25
1
1
Apr 27, 2008
#1
  • Apr 27, 2008
  • #1
Found a second problem with my new stang...The brake lights don't work!..its a 1995 5.0 5 speed......Everything else works,turn signals,parking lights, but the bulb that does the brakes light doesn't work. I haven't done any testing yet accept checked the bulbs...Is there any common problem with these? I've looked at all the fuses and they all seem good.
 
Reactions: Aaron

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Apr 27, 2008
#2
  • Apr 27, 2008
  • #2
Moved to 94-95 Tech.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Apr 27, 2008
#3
  • Apr 27, 2008
  • #3
Check the BOO. Since the TS's work, we can assume the fuse is good (it controls the BOO and TS's as I recall).

Does the 3rd brake light work? If it does, the BOO (and fuse) are ok. Power for the outer brake lights run through the MF switch, whereas power for the 3rd brake light does not. That's why knowing if the 3rd one works is important.

If you have no brake lights at all, check in/out voltage at the BOO (be sure the switch is closed when you test output voltage).

Good luck.
 

toyman

10 Year Member
Jul 19, 2007
1,944
54
79
Vernon BC
Apr 27, 2008
#4
  • Apr 27, 2008
  • #4
HISSIN50 said:
Check the BOO. Since the TS's work, we can assume the fuse is good (it controls the BOO and TS's as I recall).

Does the 3rd brake light work? If it does, the BOO (and fuse) are ok. Power for the outer brake lights run through the MF switch, whereas power for the 3rd brake light does not. That's why knowing if the 3rd one works is important.

If you have no brake lights at all, check in/out voltage at the BOO (be sure the switch is closed when you test output voltage).

Good luck.
Click to expand...

Okay, what's a BOO and where is it located? If the OP knows I don't. TS I assume is the "Turn Signal" based on the context.

Richard
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Apr 27, 2008
#5
  • Apr 27, 2008
  • #5
Sorry guys.

BOO = Brake On/Off switch. It's standard nomenclature for our brake light switches (because it's monitored by the EEC, it's no longer simply called a brake switch).

The switch is obviously on the brake pedal assembly.

You got it with TS (my made up shorthand).

MF = Multi-function switch, which is the turn signal switch. Because our tails and brakes share bulbs, the brake light wiring for the body brake lights [not the 3rd one] go through the MF switch.
 
E

epurdy2005

New Member
Apr 3, 2004
25
1
1
Apr 28, 2008
#6
  • Apr 28, 2008
  • #6
Thanks for clarification of the boo.......On my brake pedal there is the switch that comes out when the brake is pushed which looks okay and then theres something else on there with electrical wires going to it closer to the floor on the brake pedal. What is it? It had some electrical tape on it so maybe somebody has messed with it....I also found a purple neon while I was down tehre which I took out. And no the third brake light isn't working either...Thanks!
 

bigplansnomoney

New Member
Dec 11, 2007
4
0
0
Richmond, Virginia
Apr 28, 2008
#7
  • Apr 28, 2008
  • #7
I would assume maybe the wires went to some TRICK ASS neon racing pedals the previous owner may have had to accent his homo purple neons. Where does the other end of that wire run.

Try replacing that brake on/off switch first. If the third brake light functions, your Multifunction should be functioning correctly.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Apr 28, 2008
#8
  • Apr 28, 2008
  • #8
Again, check in/out voltages at the BOO.
 

94GTCoupe

10 Year Member
May 7, 2006
1,412
92
79
CA
Apr 28, 2008
#9
  • Apr 28, 2008
  • #9
to check BOO

#1.using test light,touch terminal at BLUE arrow with pedal in normal position.if test lights illuminate.switch is receivlng power.if no power here,check wiring to the BOO switch,also check fuse #9 under dash,should be 15 amp fuse.

#2.press brake pedal down,touch test light to RED arrow.if light illuminates,switch is working.

#3.if switch works,problem is most likely in the wiring.your going to need a wiring diagram,but im sorry i dont have one.


If switch needs to be replaced.

#1.disconnect wiring,BLUE arrow

#2.pull out brown pin,RED arrow.

#3.slide out in direction of PURPLE arrow.make note of the position of the plastic washer and bushing.

#4.install is reverse of removal.
 

StadEMS3

20+ Year Stangneter
Jun 19, 2003
228
43
49
Mechanicsville, MD
Apr 28, 2008
#10
  • Apr 28, 2008
  • #10
I had a similar issue, I kept blowing the brake light fuse when I pressed the clutch pedal. It turned out that my Steeda aluminum quadtrant wore a small hole in the brake wire. It wouldn't blow the fuse if it was just quickly pushed in for shifting, just when held to the floor grounded it out long enough to blow. What a troubleshooting nightmare that was.
 

toyman

10 Year Member
Jul 19, 2007
1,944
54
79
Vernon BC
Apr 28, 2008
#11
  • Apr 28, 2008
  • #11
I'm curious. How did all that rust get there when you live in Fresno?

My car spent the first 8 years on the West Coast and it's totally rust free on the underdash metal pieces.
 

94GTCoupe

10 Year Member
May 7, 2006
1,412
92
79
CA
Apr 29, 2008
#12
  • Apr 29, 2008
  • #12
the clutch pedal assembly is from a wrecked 94 GT i bought for the aode to T5 swap.it was sitting in the mountains in for almost 2 years in a very moist,grassy field before i bought it
 

Lee Gardner

New Member
Feb 5, 2016
4
0
1
Feb 12, 2016
#13
  • Feb 12, 2016
  • #13
Having this issue as well. Power to the BOO comes and goes, but I press the brake and the power goes away, where can I check to find this issue. Thanks guys
 
N

Nenecas1

New Member
Sep 26, 2020
2
0
1
colorado
Oct 19, 2020
#14
  • Oct 19, 2020
  • #14
94GTCoupe said:
to check BOO

#1.using test light,touch terminal at BLUE arrow with pedal in normal position.if test lights illuminate.switch is receivlng power.if no power here,check wiring to the BOO switch,also check fuse #9 under dash,should be 15 amp fuse.

#2.press brake pedal down,touch test light to RED arrow.if light illuminates,switch is working.

#3.if switch works,problem is most likely in the wiring.your going to need a wiring diagram,but im sorry i dont have one.


If switch needs to be replaced.

#1.disconnect wiring,BLUE arrow

#2.pull out brown pin,RED arrow.

#3.slide out in direction of PURPLE arrow.make note of the position of the plastic washer and bushing.

#4.install is reverse of removal.
Click to expand...
 
S

stevedjarrell

Member
Jun 9, 2024
22
19
13
Milford CT
Oct 22, 2024
#15
  • Oct 22, 2024
  • #15
Old thread but having a similar problem. Brake lights went out after working fine. The chime and dome light still work so I know the fuse is good (also checked it) Here is the weird thing. With the key out of the ignition now if I press the brake pedal the chime goes off and my HVAC panel lights come on. sounds weird right? this was not happening before, and I have touched nothing related to these circuits. I did read where someone with a Camaro had a similar issue and turned out to be shorted bulb, he put a dual filament bulb in. I did just change my bulbs to led, so I am going to pull them out and start there with a voltmeter / old bulbs. Would be nice if it really was just that. Just putting this up here as the symptoms are different.
 

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor
Admin Dude
Jan 4, 1985
43,106
21,284
234
Box behind Walmart
Oct 22, 2024
#16
  • Oct 22, 2024
  • #16
stevedjarrell said:
Old thread but having a similar problem. Brake lights went out after working fine. The chime and dome light still work so I know the fuse is good (also checked it) Here is the weird thing. With the key out of the ignition now if I press the brake pedal the chime goes off and my HVAC panel lights come on. sounds weird right? this was not happening before, and I have touched nothing related to these circuits. I did read where someone with a Camaro had a similar issue and turned out to be shorted bulb, he put a dual filament bulb in. I did just change my bulbs to led, so I am going to pull them out and start there with a voltmeter / old bulbs. Would be nice if it really was just that. Just putting this up here as the symptoms are different.
Click to expand...

You have a broken ground someplace.

C279 C211 S303

S302 - Splice near Tape Out next to G201
G201 - Ground in Left Fender Apron

S303 - Splice near Tape Out to windshield wiper

C211 - Connector attached to hazard switch

C279 - On Steering Column near ignition switch

There are Tape Out Grounds at each of these locations. That C279 looks like it might be a bugger to find. Looking at the diagram though, since your brake light and HVAC light are both affected then it should be the grounds at either S302 or S303. I included the others because stranger things have happened when juice has to find it's own path to ground.
 
S

stevedjarrell

Member
Jun 9, 2024
22
19
13
Milford CT
Oct 22, 2024
#17
  • Oct 22, 2024
  • #17
Believe it or not, my problem was due to an incorrect bulb that was shorted out. It was one of the marker bulbs. I took out everything I still had all the same symptoms. I put a working marker bulb, and the one that was blown and everything went back to normal. I have since replaced all the bulbs and I am. That is the weirdest symptom for a blown bulb I’ve ever seen.
 
Reactions: Noobz347

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor
Admin Dude
Jan 4, 1985
43,106
21,284
234
Box behind Walmart
Oct 22, 2024
#18
  • Oct 22, 2024
  • #18
stevedjarrell said:
Believe it or not, my problem was due to an incorrect bulb that was shorted out. It was one of the marker bulbs. I took out everything I still had all the same symptoms. I put a working marker bulb, and the one that was blown and everything went back to normal. I have since replaced all the bulbs and I am. That is the weirdest symptom for a blown bulb I’ve ever seen.
Click to expand...

Huh... I wonder if it was shunted to ground somehow.
 
You must log in or register to reply here.

Similar threads

8
Grounding issue?
  • 86SilverFox
  • May 16, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
164
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 31, 2026
86SilverFox
8
P
Is it normal for all of this to go wrong or did I get played when I bought this ONLY A MONTH AGO.
  • ponygal02
  • Nov 14, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
272
1996 - 2004 SN95 Mustang -General/Talk- Nov 14, 2025
Noobz347
A
1966 Mustang coupe / Brake lights and left rear turn signal not working.
  • ArizonaRob1966
  • Nov 3, 2025
  • Classic Mustang Specific Tech
Replies
2
Views
371
Classic Mustang Specific Tech Dec 24, 2025
Mcmahst
M
Need help!
  • Masonevans726
  • Dec 17, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
242
1996 - 2004 SN95 Mustang -General/Talk- Dec 17, 2025
Masonevans726
M
T
Progress Thread 2002 Mustang 3.8L CV
  • TheIncompetentMechanic
  • May 26, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
81
1996 - 2004 SN95 Mustang -General/Talk- Jun 1, 2026
TheIncompetentMechanic
T
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?