• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Brake Question--Not about upgrade

  • Thread starter Thread starter timhodge
  • Start date Start date Jan 31, 2009
T

timhodge

Founding Member
Aug 22, 2001
89
0
6
Jan 31, 2009
#1
  • Jan 31, 2009
  • #1
Well, I guess it kind of is, but not really.
I upgraded my 89 with 95 disk parts. Went pretty well. Used 93 cobra booster with the 95 master cyl.
Got everything bled and the pedal is hard as a rock, after starting engine, I get about 2 extra inches of travel in the pedal and no amount of bleeding, including re-bleeding the mc, seems to get rid of it. The pushrod is set to spec. I can't find any leaks, so I don't know what to try next. I'm thinking the mc maybe has a weak seal that only shows up under the increased pressure with the booster activated. If there are no other ideas I will try changing the mc next but I would really appreciate any help/ideas. Thanks in advance. Tim
 
T

timhodge

Founding Member
Aug 22, 2001
89
0
6
Feb 10, 2009
#2
  • Feb 10, 2009
  • #2
Well, I worked on it a little more this weekend. I plugged the line to the front at the mc and the pedal firmed right up. Plugged the line to the rear and mushy again so I checked the caliper pistons for excess movement and they are moving in about 1/8 to 3/16 inch each pedal push. Then moving back out the same amount when released instead of staying up against the rotor. I think this is too much but not sure why it's doing it. This is with the car up on jacks and no wheel movement. Right now I'm thinking I'll drive it a little and see if they will seat up a little better with some wear. Otherwise I guess just try some new rotors and calipers. The pads are new.
Any other thoughts or ideas welcome, as always.
 

Blandnuts

I don't swallow; I only swoosh
Founding Member
Aug 21, 2000
1,172
124
124
FloorDuh
Feb 10, 2009
#3
  • Feb 10, 2009
  • #3
Did you bench bleed the mc? What did you set the pushrod to? What was your method of bleeding the brakes? Not trying to be an ass, just trying to get a base on what was done.


Fred
 
T

timhodge

Founding Member
Aug 22, 2001
89
0
6
Feb 11, 2009
#4
  • Feb 11, 2009
  • #4
Blandnuts said:
Did you bench bleed the mc? What did you set the pushrod to? What was your method of bleeding the brakes? Not trying to be an ass, just trying to get a base on what was done.


Fred
Click to expand...

Did you bench bleed the mc? yes

What did you set the pushrod to? around 31/32

What was your method of bleeding the brakes? Plain old 2 man method, with an assist by tapping the calipers with a rubber mallot. Have heard the 95 calipers tend to hide some air, and this helps to dislodge it.

Not trying to be an ass, just trying to get a base on what was done. Not a problem. Thanks for the interest.

Tim
 

Blandnuts

I don't swallow; I only swoosh
Founding Member
Aug 21, 2000
1,172
124
124
FloorDuh
Feb 11, 2009
#5
  • Feb 11, 2009
  • #5
That's odd it got better when you closed off the front brakes. Are the brakes consistent when driving? How's the stopping power? What proportioning valve did you use, and how did you set it to bleed the brakes?


Maybe I'll eventually stop asking questions



Fred
 
T

timhodge

Founding Member
Aug 22, 2001
89
0
6
Feb 12, 2009
#6
  • Feb 12, 2009
  • #6
Blandnuts said:
That's odd it got better when you closed off the front brakes. Are the brakes consistent when driving? How's the stopping power? What proportioning valve did you use, and how did you set it to bleed the brakes?


Maybe I'll eventually stop asking questions



Fred
Click to expand...

Haven't driven it much at all. Drove about a mile and tried some panic stops. The brakes work, but couldn't lock up the wheels. No pulling, strange noises or anything else unusual though. I'm still considering putting a few more miles on it, and see if the pads seat in better.
Used the FMS prop. valve set at max rear brake, can't remember if that's all the way in , or out, but you know what I mean.
Ask away, I'm not going anywhere.
Tim
 

Blandnuts

I don't swallow; I only swoosh
Founding Member
Aug 21, 2000
1,172
124
124
FloorDuh
Feb 12, 2009
#7
  • Feb 12, 2009
  • #7
Yeah, put a few miles on it. Here's a site to help bed-in your brakes. It seems like you did all the work right and after proper bedding of the brakes you should have better stopping power. I'm still not fond that the pedal goes almost to the floor.... Anyways, post back up if you find anything.


Fred
 

Blandnuts

I don't swallow; I only swoosh
Founding Member
Aug 21, 2000
1,172
124
124
FloorDuh
Feb 12, 2009
#8
  • Feb 12, 2009
  • #8
Instructions for bedding in your brakes
 
You must log in or register to reply here.

Similar threads

D
Brakes 1966 Mustang convertible 289, Auto - Disc brake conversion issues
  • DRGunn427
  • Feb 26, 2025
  • Classic Mustang Specific Tech
Replies
5
Views
901
Classic Mustang Specific Tech Jul 23, 2026
All Stock93
1970 brake issue. Bad booster or?
  • All Stock93
  • May 13, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
10
Views
858
1965 - 1973 Classic Mustangs -General/Talk- Sep 13, 2025
All Stock93
C
Fox Cobra Style Brake booster kit
  • Crigano
  • Aug 17, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 25, 2024
AeroCoupe
Brakes ‘93 Cobra Brake Booster and Master Cylinder Question
  • Willybill32
  • Jun 28, 2023
  • Fox 5.0 Mustang Tech
Replies
13
Views
3K
Fox 5.0 Mustang Tech Jun 30, 2023
Willybill32
E
Finished my Fox Hydroboost Install - Tips
  • Engineer Duane
  • Apr 9, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 5, 2025
Engineer Duane
E
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?