• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Burned up my driverside window motor.

  • Thread starter Thread starter dec322
  • Start date Start date May 5, 2006
D

dec322

Member
Feb 11, 2006
401
2
16
Bham AL
May 5, 2006
#1
  • May 5, 2006
  • #1
I've got the door panels off and wires are everywhere b/c I'm putting some sound deadening material in the doors. Well I was rolling the window up (or maybe down and the wires to the window motor was caught in track/gear looking thing. Well, it stopped. When I freed all the wires and tried to roll it up nothing happened. I think its burned up b/c there is no noise and it doesn't put any drain on the charging system. I pulled the motor out in order to push the window back up. Is there any way to test the motor? I think its the original motor......


Also, while on the subject, sometimes when I'm rolling the passenger side window up there is a long pause from the time I push the button to the window actually going up. I never have a problem with it going down and the problem going up doesn't happen if I don't take it to the bottom of the door. Any guesses?
 

bigcat

start with the upper hole, and if more traction is
May 1, 2005
3,015
1
79
7200 feet
May 5, 2006
#2
  • May 5, 2006
  • #2
you can test it by hooking the two wires directly to a 12V source, like a battery.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 5, 2006
#3
  • May 5, 2006
  • #3
A ground might help for bench testing too.
 
D

dec322

Member
Feb 11, 2006
401
2
16
Bham AL
May 5, 2006
#4
  • May 5, 2006
  • #4
Thanks for the replies yall but I need some specifics on how to do this....how do I hook it up to a battery? How do I do the ground? Electronics are not my thing.
 

bigcat

start with the upper hole, and if more traction is
May 1, 2005
3,015
1
79
7200 feet
May 5, 2006
#5
  • May 5, 2006
  • #5
you should be able to use some speaker wire, if that is all you have, and put one end on the +, and one end on the - of the battery. it does not matter which end goes where on the motor connection. if you swap the wires, it will go the opposite direction.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 6, 2006
#6
  • May 6, 2006
  • #6
Remove the door mounted speaker & the upholstery panel to gain access to the motor. There are 3 screws (5/16" hex head, I think) that secure the motor in place. Remove them and the motor comes out without any problems. Once you remove all the screws from the motor, and it falls away from the gear teeth on the arm for the glass, the glass will move up and down. You may need a helper to hold the glass once the motor screws are out, since the gear on the motor holds the glass from sliding up or down

The motor is the same for left side or right side, only the gearboxes are different. If you can't find the complete assembly for the side you want, you can get either side and use the old gearbox on the new motor.
 
D

dec322

Member
Feb 11, 2006
401
2
16
Bham AL
May 6, 2006
#7
  • May 6, 2006
  • #7
jrichker said:
Remove the door mounted speaker & the upholstery panel to gain access to the motor. There are 3 screws (5/16" hex head, I think) that secure the motor in place. Remove them and the motor comes out without any problems. Once you remove all the screws from the motor, and it falls away from the gear teeth on the arm for the glass, the glass will move up and down. You may need a helper to hold the glass once the motor screws are out, since the gear on the motor holds the glass from sliding up or down

The motor is the same for left side or right side, only the gearboxes are different. If you can't find the complete assembly for the side you want, you can get either side and use the old gearbox on the new motor.
Click to expand...


Yeah, I removed the motor last night in order to push my window out. I guess I'll just go ahead and buy a new one. Just one of those things I guess.
 
You must log in or register to reply here.

Similar threads

B
Front window issues
  • bruno
  • Nov 7, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
213
Fox 5.0 Mustang Tech Tuesday at 10:26 PM
AeroCoupe
D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
207
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
Door wire harnesses 1996 GT
  • Adizzle843
  • Feb 5, 2026
  • SN95 4.6L Mustang Tech
Replies
7
Views
542
SN95 4.6L Mustang Tech Feb 17, 2026
Adizzle843
Electrical Fried my window motor…
  • AnthonyA1234
  • Oct 25, 2024
  • Fox 5.0 Mustang Tech
Replies
8
Views
608
Fox 5.0 Mustang Tech Oct 26, 2024
General karthief
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
529
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?