Cam Shafts Help......

red_stang_225

New Member
Aug 4, 2005
14
0
0
Cam Shafts Help
hi guys

im a new member here so i need some help for my friend

its a 2001 Automatic tranny

and here is the stuff

3.73 ratio
long tube hooker headers
BBK H pipe
40 series flowmaster mufflers
75mm BBk throttle
BBK ram air
K&N filter
BBK pullys
TCI cooler gear
Shift kit transgo
SCT computer programmer
intake flow and spacer

so we need a good cam for these parts

what do u guys prefer?

and wich converter is good with the cam lift?

yeah and we need all parts we need for the cam shafts

springs,lockers,,,,etc

so plz we need ur help
 
For a GT with those mods, I'de get a 3000+rpm stall converter from Precision Industries with a set of VT Engine Stage II cams.

EDIT: With Stage II cams, you will need aftermarket valve springs.
 
red_stang_225 said:

http://www.tccoa.com/articles/tranny/shiftybusiness.html

The Jerry mod shift kit is a shift kit that uses the stock valve body and seperator plate. You just need to enlarge some holes and remove a few springs from the ac***ulator pistons. That link should guide you through how to do it. Although its a Thunderbird and Cougar club and the article was written for Thunderbirds, still, the Thunderbird uses the same transmission as our Mustangs do in the automatic versions, the 4r70w automatic to be specific. It should make the differences between the years and versions clear and what to do for your application.
 
98MACH1R said:
hey dude im not knocking you but those numbers look kinda low is you a/f ratio out of wack or something? :shrug:
You must remember, he does have an automatic transmission. They tend to produce lower numbers. I will agree though, for his mods the numbers are just a tad low.
 
Yeah, I'd have to agree. I made the same power with 4.10's, CAI, Bullitt intake, o/r X, and a mail order tune.
For having a cat-back, L/T's, and a higher gear, he should be in the mid to high 230's.
 
thnx guys

ok im another friend for the owner of this user he told me to log in here

ok

the owner of the GT wnet to so many places and everybody told him nothing wrong so how can he know if there is something wrong

and when he floor it from 0 the RPM stick at 3000's a few seconds then it goes up normal,why is that?

maybe there is something wrong in the drive train

from tranny or the final end

btw the rear tires are 295/50/15

i think they r too heavy
 
His #'s may just be lower than the average (there's an average for a reason). As far as the rpm hangin' at 3K; that's probably that POS Transgo kit. Like I said, lose that junk and see where you're at afterward.
 
red_stang_225 said:
thnx guys

ok im another friend for the owner of this user he told me to log in here

ok

the owner of the GT wnet to so many places and everybody told him nothing wrong so how can he know if there is something wrong

and when he floor it from 0 the RPM stick at 3000's a few seconds then it goes up normal,why is that?

maybe there is something wrong in the drive train

from tranny or the final end

btw the rear tires are 295/50/15

i think they r too heavy
Tell me, is there any tire spin when he floors it from a dead stop ? If so, that could explain the rpm sticking and hesitating to climb. Two, is the stock torque converter still in the car or is there an aftermarket torque converter in there ? '01 Steed could be correct. The transgo shift kit could be messing something up if not installed properly. One thing to remember with ANY shift kit is never put any blocker rings in the accumulator pistons and NEVER EVER increase/decrease line pressure unless if you know what you're doing.