• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

camshaft bearing help

  • Thread starter Thread starter MarSaleenMustan
  • Start date Start date May 3, 2005
M

MarSaleenMustan

Founding Member
Apr 5, 2002
208
0
0
San Bernardino California
May 3, 2005
#1
  • May 3, 2005
  • #1
so today i was going to install the camshaftbearings and camshaft. i put in the bearings into the bores of each cam bore. yes i made sure each bearing went into the bore that it was supposed to since the smallest diameter bore is the closest to the flywall and they get bigger as you move up to the front one.
My teacher put in the first two(closest to the back) and i slid in the last three. when we went to slide the cam in it wouldnt go in all the way. at first we thought it could be the first(furthest back) bearing we installed, but upon further inspection we noticed it was the second to last, so we took it out, slid the cam in without it and sure enough it went all the way through smoothly and turned. so we pulled the cam out again and sure enough, the bearing would clear the first bearing journal but it wouldnt go in to the second, we also turned it over to see if it would go in from the other side but nothing, so i took the old one from the same journal and it did go in. so i had to go to the napa wearehouse store which was about 20 mins away, brought it back to the shop. slid it over the first journal no problem, then the second(which its supposed to be for) and it did just clear it. so we knew we had had a miss machined bearing from the first set. so i go to slide it in(all of this witht he proper tool which is driven by a hand hammer) and it goes in. then i go to slide the camshaft and it goes in abuot 1/8th on all journals, so i start turning int and pushing at the same time but the damn bearing starts to turn too and slide! I hope its not the bore thats somehow gotten a bit too big for the bearing because according to my teacher the block would be junk unless it was bored out and had a sleeve put in which would cost too much for me to do it. so i was wondering if theres any way to make it work. i mean who knows, if i got a bad bearing the first time, whose to say the second one isnt bad either I'm going to go by the ford dealership and see if they have these bearings, hopefully those work. any ideas?


__________________
 
M

MarSaleenMustan

Founding Member
Apr 5, 2002
208
0
0
San Bernardino California
May 4, 2005
#2
  • May 4, 2005
  • #2
anyone?
 
M

MarSaleenMustan

Founding Member
Apr 5, 2002
208
0
0
San Bernardino California
May 6, 2005
#3
  • May 6, 2005
  • #3
thanks to those who responded seems like not many people have built/rebuilt engines around here. i guess next time I'll title my thread "need help with figuring rear end gear ratio" to get more attention.

got the problem solved by the way
 

ExplodingGopher

New Member
Jun 11, 2004
517
0
0
The mistake on the lake (Ohio)
May 6, 2005
#4
  • May 6, 2005
  • #4
I'm not sure about this problem, but when you have a technical problem like this i always post it on this forum: http://www.network54.com/Forum/85220

Its a ford 385 series engine forum, but they are all great engine builders and machinists and they can definitely help you out. They have helped me through my entire 466 swap.
 
You must log in or register to reply here.

Similar threads

Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
730
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
N
Vibration after new clutch
  • nipple_looker
  • Sep 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
23
Views
733
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 26, 2026
fasterthangas
F
Engine Obstinate Pilot Bearing removal
  • FastDriver
  • Feb 12, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
40
Views
1K
Fox 5.0 Mustang Tech Feb 22, 2026
manicmechanic007
W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
295
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
Electrical problem plug in the drivers kick panel
  • Mindseye007
  • Aug 16, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
242
Fox 5.0 Mustang Tech Aug 16, 2026
Mindseye007
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?