• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Engine Car Sat For A Week, Now Has A Loud Tick

  • Thread starter Thread starter Moodswing5.0
  • Start date Start date Aug 9, 2013

Moodswing5.0

New Member
Jul 29, 2012
12
0
2
Lancaster, California
Aug 9, 2013
#1
  • Aug 9, 2013
  • #1
A couple weeks ago I had some sewing machine ticking from my valve train. I run Holley Aluminum heads, crane cam rockers, and hyd lifters. So I went through and retorqued everything to spec. Perrred like a kitten and ran better too. Then I smoked the clutch, been sitting for a couple weeks so today I started it up, pretty loud tick. Let it sit for 5-10 min to see if it would go away...stayed.
Could the hydraulic lifters be the cause? I pulled the intake and valve covers back of to inspect and there is no broken parts or bent rods. Oil pressure shows good and it has plenty of oil.
 

CT Grim

Member
Aug 5, 2013
40
9
19
Tucson, AZ
Aug 11, 2013
#2
  • Aug 11, 2013
  • #2
Collapsed lifter?
 

vfast

Member
Aug 14, 2012
113
1
19
Va
Aug 11, 2013
#3
  • Aug 11, 2013
  • #3
check your push rods if they can turn,,recheck rockers...see if a rocker is off center..you can use a pushrod to test is you can a weak one put some oil on top and pump it lightly
do you have stock headers on engine? if not may be a gasket leak
 

mikestang63

SN Certified Technician
Aug 27, 2012
11,606
8,859
214
In the garage
Aug 11, 2013
#4
  • Aug 11, 2013
  • #4
try and isolate the clicking noise with the car running. There are several methods to listen in on a sound- wooden dowel, stethoscope, large piece of fuel hose, placed on the valve covers and to your ear. Is the reason you smoked the clutch due to high rpm launches? You could have either collapsed a lifter, bent a pushrod or rocker shaft or a weak spring. As memtioned. check to see all the valvetrain is snug and the pushrods are not bent. All of the rockers should be centered on the valve stem and the springs not binding or collapsed, Crank over the motor a few times with the covers off to see the valvetrain move and to hear any noise.
 

vfast

Member
Aug 14, 2012
113
1
19
Va
Aug 11, 2013
#5
  • Aug 11, 2013
  • #5
i would also look at the valve cover to see if a rocker wasn't hitting it
 

CT Grim

Member
Aug 5, 2013
40
9
19
Tucson, AZ
Sep 15, 2013
#6
  • Sep 15, 2013
  • #6
Didja get it figured out?
 
You must log in or register to reply here.

Similar threads

6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
4
Views
896
1965 - 1973 Classic Mustangs -General/Talk- Jun 20, 2026
gray owl
G
G
2006 Mustang GT o2 Sensor Wiring Issue Car Bogging/Choking
  • GCantero93
  • Sep 5, 2025
  • 2005 - 2009 Specific Tech
Replies
4
Views
1K
2005 - 2009 Specific Tech Sep 6, 2025
Noobz347
Engine Rocker Noise after Aluminum heads and 1 piece CM Pushrods
  • 79pace
  • Apr 12, 2022
  • Fox 5.0 Mustang Tech
Replies
17
Views
4K
Fox 5.0 Mustang Tech Apr 19, 2022
Monkeybutt2000
M
J
Progress Thread Family member 1989 GT- Backstory and updates
  • JRC99
  • Apr 19, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
15
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 26, 2025
JRC99
J
A
1991 5.0 with HCI - started car, running for a few minutes, started pushing coolant into the overflow tank and then puking out from there. I'm lost
  • AmericanMuscle4.6GT
  • Oct 16, 2022
  • Fox 5.0 Mustang Tech
Replies
6
Views
4K
Fox 5.0 Mustang Tech Nov 30, 2022
CAMTWO1070
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?