• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

car wont start

  • Thread starter Thread starter BK_CAULEY
  • Start date Start date Feb 25, 2007
  • 1
  • 2
  • 3
Next
1 of 3 Next Last

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 25, 2007
#1
  • Feb 25, 2007
  • #1
hey guys i just purchased a 1990 coupe this weekend and it wont start. it turns over fine but wont run. ive dried pulling the codes but it keeps giving me 11 no codes found. i am getting spark to the plugs and fule up to the rails but im not sure if its going through the injectors. any idea's? i really want to get it running.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 25, 2007
#2
  • Feb 25, 2007
  • #2
come on now

come on guys i know somebody has some answers.
 

goodfastncheap

Member
Dec 25, 2006
100
0
17
Bellevue, NE
Feb 25, 2007
#3
  • Feb 25, 2007
  • #3
Was it running when you bought it, or had it sat not running for a while? How long? Sounds like you have fuel pressure, you DO hear the pump when you turn the key to on, right?

You might get the tester that checks for signal at the injector connectors. Also check compression on all cyls.

What other symptoms? What else have you been able to rule out?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 25, 2007
#4
  • Feb 25, 2007
  • #4
If you had bothered to use the Search function, you probably would have found about 5000 copies of this...

Cranks OK, but No Start Checklist for Fuel Injected Mustangs

Revised 20-Jan-2007 to include TPS voltage out of range fault.
All text applies to all models unless stated otherwise.

Note: 94-95 specific changes are in red

1.) Remove push on connector from starter solenoid and turn ignition switch on. Place car in neutral or Park and set the parking brake. Remove the coil wire from distributor & and hold it 3/8” away from the engine block. Jumper the screw to the big bolt on the starter solenoid that has the battery wire connected to it. You should get a nice fat blue spark.
Most of the items are electrical in nature, so a test light, or even better, a voltmeter, is helpful to be sure they have power to them.
No spark, possible failed items in order of their probability:
A.) MSD or Crane ignition box if so equipped
B.) Coil
C.) TFI module
D.) PIP sensor in distributor. See paragraph 5A - a noid light will tell if the pip is working by flashing when the engine is cranking.
E.) No ECC or computer power - ECC or computer relay failure
86-93 models only: ECC relay next to computer - look for 12 volts at the fuel injector red wires
94-95 models only: EEC or PCM power relay in the constant control relay module. Look for 12 volts at the fuel injector red wires.
F.) No ECC or computer power - fuse or fuse link failure
86-93 models only: Fuse links in wiring harness - look for 12 volts at the fuel injector red wires. All the fuse links live in a bundle up near the starter solenoid.
94-95 models only: 20 amp EEC fuse in the engine compartment fuse box. Look for 12 volts at the fuel injector red wires.
G.) Ignition switch - look for 12 volts at the ignition coil red/lt green wire.
H.) Computer
J.) Engine fires briefly, but dies immediately when the key is released to the Run position. Crank the engine & when it fires off, pull the small push on connector (red wire) off the starter relay (Looks like it is stuck on a screw). Hold the switch in the crank position: if it continues to run there is a problem with either the ignition switch or TFI module. Check for 12 volts at the red/green wire on the coil with the switch in the Run position. Good 12 volts, then replace the TFI.

See the following links for wiring diagrams...

http://www.autozone.com/servlet/UiB..._us/0900823d/80/16/71/3c/0900823d8016713c.jsp for 79-88 model cars
Computer/fuel pump/ignition wiring diagram, 86 model http://www.autozone.com/images/cds/gif/large/0900823d80167158.gif
Computer/fuel pump/ignition wiring diagram, 87 model http://www.autozone.com/images/cds/gif/large/0900823d8016715e.gif
Computer/fuel pump/ignition wiring diagram, 88 model http://www.autozone.com/images/cds/gif/large/0900823d80167162.gif

http://www.autozone.com/servlet/UiB..._us/0900823d/80/19/59/5a/0900823d8019595a.jsp for 89-93 model cars
Computer/fuel pump/ignition wiring diagram, 89-90 cars http://www.autozone.com/images/cds/gif/large/0900823d8019595f.gif
Computer/fuel pump/ignition wiring diagram, 91-93 cars
http://www.autozone.com/images/cds/gif/large/0900823d80195960.gif

http://www.autozone.com/servlet/UiBroker?ForwardPage=/az/cds/en_us/0900823d/80/1d/db/3c/0900823d801ddb3c.jsp for 94-98 model cars

2.) Spark at coil wire, pull #1 plug wire off at the spark plug and check to see spark. No spark, possible failed items in order of their probability:
A.) Moisture inside distributor – remove cap, dry off & spray with WD40
B.) Distributor cap
C.) Rotor
D.) Spark Plug wires
E.) Coil weak or intermittent - you should see 3/8" fat blue spark with a good coil

3.) Spark at spark plug, but no start.
Next, get a can of starting fluid (ether) from your local auto parts store: costs a $1.30 or so. Then pull the air duct off at the throttle body elbow, open the throttle, and spray the ether in it. Reconnect the air duct and try to start the car. Do not try to start the car without reconnecting the air duct.
Two reasons:
1.) If it backfires, the chance for a serious fire is increased.
2.) On Mass Air cars, the computer needs to measure the MAF flow once the engine starts.
If it starts then, you have a fuel management issue. Continue the checklist with emphasis of fuel related items that follow. If it doesn’t, then it is a computer or timing issue: see Step 4.​

Clue – listen for the fuel pump to prime when you first turn the ignition switch on. It should run for 5-20 seconds and shut off. To trick the fuel pump into running, find the ECC test connector and jump the connector in the Upper RH corner to ground.


If the relay & inertia switch are OK, you will have power to the pump. Check fuel pressure – remove the cap from the schrader valve behind the alternator and depress the core. Fuel should squirt out, catch it in a rag. Beware of fire hazard when you do this. In pinch you can use a tire pressure gauge to measure the fuel pressure. It may not be completely accurate, but you will have some clue as to how much pressure you have. If you have any doubts about having sufficient fuel flow/pressure, rent a fuel pressure test gauge from the auto parts store. That will tell you for sure if you have adequate fuel pressure.


4.) No fuel pressure, possible failed items in order of their probability:
A.) Tripped inertia switch – Coupe & hatch cars hide it under the plastic trim covering the driver's side taillight. Use the voltmeter or test light to make sure you have power to both sides of the switch
B.) Fuel pump power relay – located under the driver’s seat in most stangs built before 92. On 92 and later model cars it is located below the Mass Air Flow meter. Look for 12 volts at the Pink/Black wire on the fuel pump relay.
C.) Clogged fuel filter
D.) Failed fuel pump
E.) 86-93 models only: Blown fuse link in wiring harness. Look for 12 volts at the Orange/Lt Blue wire on the fuel pump relay. The fuse links live in the wiring harness near the starter solenoid.
94-95 models only: 20 amp fuel pump fuse in the engine compartment fuse box. Look for 12 volts at the Dark green/yellow wire on the constant control relay module.
F.) Fuel pressure regulator failed. Remove the vacuum line from the regulator and inspect for fuel escaping while the pump is running. If fuel is coming out the vacuum port, the regulator has failed.

5.) Fuel pressure OK, the injectors are not firing.
A.) A noid light available from any auto parts store, is one way to test the injector wiring.
The noid light plugs into the fuel injector harness in place of any easily accessible injector.
B.) I like to use an old injector with compressed air applied to the injector where the fuel rail would normally connect. I hook the whole thing up, apply compressed air to the injector and stick it in a paper cup of soapy water. When the engine cranks with the ignition switch on, if the injector fires, it makes bubbles. Cheap if you have the stuff laying around, and works good too.
D.) Pull an injector wire connector off and look for 12 volts on the red wire when the ignition switch is on.
E.) No power, then look for problems with the 10 pin connecter (salt & pepper shakers at the rear of the upper manifold).
F.) No power and the 10 pin connections are good: look for broken wiring between the orange/black wire on the ECC relay and the red wire for the 10 pin connectors.
G.) TPS voltage exceeds 3.7 volts with the throttle closed. This will shut off the injectors, since the computer uses this strategy to clear a flooded engine. Use a DVM, a pair of safety pins, and probe the black/white and green wires to measure the TPS voltage. It should be .5-.99 volts with the key on, engine not running. Note that if the black/white wire (signal ground) has a bad connection, you will get some strange readings. Make a second measurement using the battery post as the ground to eliminate any ground problems. If the readings are different by more than 5%, you may have a high resistance condition in the black/white signal ground circuit.

6.) Spark & fuel pressure OK.
A.) Failed IAB (no airflow to start engine). Press the throttle ¼ way down and try to start the car.
B.) Failed computer (not very likely)
C.) Engine ignition or cam timing off: only likely if the engine has been worked on recently).
D.) Firing order off: HO & 351 use a different firing order from the non HO engines.
HO & 351W 1-3-7-2-6-5-4-8
Non HO 1-5-4-2-6-3-7-8
E.) No start when hot - Press the throttle to the floor & try starting it if you get this far. If it starts, replace the ECT.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 25, 2007
#5
  • Feb 25, 2007
  • #5
yea i searched

yea i used the search but found know help.i am getting good fuel to the injector rails (previous owner installed gauge) so yes i have good pressure and yes the pump works. no it was not running when i got it but was running the previous day thats why he sold it to me because he was tired of working on it. and i am getting good ignition. and YES jrichker i found about 5000 copies of that. any starting point would be helpfull thiugh guys.
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Feb 25, 2007
#6
  • Feb 25, 2007
  • #6
did you check compression?
 

JChalfan

Member
Nov 27, 2002
551
0
16
Bellevue, WA
Feb 25, 2007
#7
  • Feb 25, 2007
  • #7
If it was just running, I wouldn't worry about a compression check quite yet.

Get a noid light to see if the injectors are firing.

You said you have spark, correct? Maybe the previous owner took the distributor out and put it back in wrong. Get the engine to TDC on the compression stroke and pull the distributor cap off to see if the rotor is pointed at #1 plug wire.

If neither one of those (relatively) easy things finds the problem, then follow jrichkers checklist line by line.
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Feb 25, 2007
#8
  • Feb 25, 2007
  • #8
JChalfan said:
If it was just running, I wouldn't worry about a compression check quite yet.

Get a noid light to see if the injectors are firing.

You said you have spark, correct? Maybe the previous owner took the distributor out and put it back in wrong. Get the engine to TDC on the compression stroke and pull the distributor cap off to see if the rotor is pointed at #1 plug wire.

If neither one of those (relatively) easy things finds the problem, then follow jrichkers checklist line by line.
Click to expand...

Thats a good point. But I would not trust that the engine was running the day befre unless he is a good friend.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 25, 2007
#9
  • Feb 25, 2007
  • #9
the list

yea i was riding in the car when it died. we were heading to the store and ran out of gas we went and got some gas in a can to put in it and it wouldnt crank back up. i thought it might be the fuel filter and he was like you know what i dont care. you want it give me $1500 for it . (i will go into detail of what it is later) which was a steal gas it was a special service vehicle, and yes i ran the vin and door codes to make sure anyways i got home put on a new filter and still no crank. im getting spark and all but not sure if the injectors are delivering fuel. and i tried everything on the list. where can i get one of those injector (noid) lights from.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Feb 25, 2007
#10
  • Feb 25, 2007
  • #10
Keith, take a deep breath and re-read Joe's list. If the solution is not on his list, go check the plumbing on your kitchen sink because that's where the solution lies (in other words, I don't recall coming across an issue not covered on the list).

You will see that in 5A, JR mentions the noid light which you are asking about. If you covered all the bases in that list, you'd have done this test already.

Print that list out, highlight what you have NOT thoroughly checked out yet (no cheating. Best to test twice than assume, or do an invalid test and chase your tail for 2 weeks. Been there and done that). Then makes notes in the margin of the print-out as you go. You will find the issue in short order if you do this.

Good luck.
 

goodfastncheap

Member
Dec 25, 2006
100
0
17
Bellevue, NE
Feb 25, 2007
#11
  • Feb 25, 2007
  • #11
Keith,

Think back. Just before it "ran out of gas", did your friend hit the rev limiter?

If you did do everything on the list, as you say, then maybe it's something mechanical, and it's time to check comp.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 25, 2007
#12
  • Feb 25, 2007
  • #12
one more time

HISSIN- printing now and yes i am getting in a bit of a hurry. but thought i covered it pretty good.

GOODFASTANDCHEAP- no we didnt hit the rev limiter he was driving like an old lady cause we knew we where about to be out of gas.

if anyone can think of anything else let me know.
 

JChalfan

Member
Nov 27, 2002
551
0
16
Bellevue, WA
Feb 25, 2007
#13
  • Feb 25, 2007
  • #13
BK_CAULEY said:
HISSIN- printing now and yes i am getting in a bit of a hurry. but thought i covered it pretty good.

GOODFASTANDCHEAP- no we didnt hit the rev limiter he was driving like an old lady cause we knew we where about to be out of gas.

if anyone can think of anything else let me know.
Click to expand...

Noid light, noid light, noid light.

In the past I've used a simple test light and pierced a wire going into the injector, and the test light would flash when the injector was firing. Of course it's probably a good idea not to pierce an injector wire... I've heard that auto parts stores have noid lights. I don't know if they rent them or sell them...

Good luck, you'll get it figured out. I bet it ends up being something simple, and you end up with a hell of a deal on the car.
 

goodfastncheap

Member
Dec 25, 2006
100
0
17
Bellevue, NE
Feb 25, 2007
#14
  • Feb 25, 2007
  • #14
I know it's bad to guess, but I have a theory.

One thing "the list" doesn't address is timing. Make sure, with #1 at TDC on the compression stroke, that the rotor is pointing at the #1 plug post.

You need to eliminate a sheared distributor gear pin or crank keyway.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 25, 2007
#15
  • Feb 25, 2007
  • #15
NOW I GOT BIGGER PROBLEMS

ok guys now im really F***** becaus i was turning it over so much the battey died and i took the battery off my GF's 89 and left it running and put y battery on it to charge it and now her car is surging and not throwing any codes. WTF!!
 

JChalfan

Member
Nov 27, 2002
551
0
16
Bellevue, WA
Feb 25, 2007
#16
  • Feb 25, 2007
  • #16
BK_CAULEY said:
ok guys now im really F***** becaus i was turning it over so much the battey died and i took the battery off my GF's 89 and left it running and put y battery on it to charge it and now her car is surging and not throwing any codes. WTF!!
Click to expand...

So to be clear, you took the battery out of the 89 while it was running and swapped your dead battery into the 89, and it's running the whole time?

Disconnecting the battery on a computer controlled car while the engine is running can destroy a computer. I've done it, but not on a mustang. Mustang computers seem to be pretty resistant to voltage spikes (in my experience), but it's definitely possible to damage one.

Maybe pull the computer out of your car and put it in hers, and see if it fixes the surge? You can put an auto computer in an auto or 5speed, but a 5speed computer won't work in an auto (so I'm told, never tried.)
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Feb 25, 2007
#17
  • Feb 25, 2007
  • #17
noid light

other than getting a noid light and checking my injectors i cant find an issue. i took the TPS and the mass air meter off of my old motor and installed it on it and still got nothing and i made sure the TPS is set at .97 volts. i tried to spray starting fluid in the intake and it wouldnt even start with that. and i have good spark. i pulled all of the plugs individually and one at a time and they all had good spark so now im at a loss. and why do i have a WELL'S box on this car? i have had 3 other 5.0's and didnt have it or at least i never saw it. could that have anything to do with it not cranking. doesnt it have something to do with the ignition? and if anybody knows why my GF's car is surging at cutting off after i disconnected the battery and can tell me how to fix it let me know. thanks guys.
 

JChalfan

Member
Nov 27, 2002
551
0
16
Bellevue, WA
Feb 25, 2007
#18
  • Feb 25, 2007
  • #18
What's a WELL'S box?
 

302RollinHard

New Member
Sep 26, 2005
0
0
0
Columbus, OH
Feb 26, 2007
#19
  • Feb 26, 2007
  • #19
You may have gotten yourself into a pickle here with the lady's car, my friend. As mentioned above, you shouldn't ever disconnect the battery to a running car EEC controlled car. Sometimes it might not hurt anything but it only takes once. A dead (or substantially drained) battery will make your car run like crap. Also you shouldn't put a dead battery into a car if at all possible as it might overload and burn up the alternator. You should recharge a dead battery before installing it. Were the spark plugs wet when you pulled them out of your car? If you have been cranking that long with no start, they should have some gas on them.
 

goodfastncheap

Member
Dec 25, 2006
100
0
17
Bellevue, NE
Feb 26, 2007
#20
  • Feb 26, 2007
  • #20
Once again did you check to make sure with #1 on TDC of the compression stroke that the rotor points to #1 post?

But I suppose now you have to fix your girlfriend's car first...
 
  • 1
  • 2
  • 3
Next
1 of 3 Next Last
You must log in or register to reply here.

Similar threads

B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
533
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
M
Electrical 93 5.0 No Injector Pulse
  • machinermac
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
15
Views
524
Fox 5.0 Mustang Tech Aug 1, 2026
Willybill32
9
1997 gt Starts then dies a few seconds after.
  • 97orange
  • Aug 13, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
321
SN95 4.6L Mustang Tech Aug 17, 2026
97orange
9
B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
602
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?