• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Clutch Fork Help

  • Thread starter Thread starter 5.0 Nostalgia
  • Start date Start date Mar 15, 2008

5.0 Nostalgia

10 Year Member
Feb 28, 2003
904
5
39
CT
Mar 15, 2008
#1
  • Mar 15, 2008
  • #1
Ok, bare with me on this one. I am having a problem installing a clutch fork. I just removed my extended clutch fork because I could not get the clutch cable properly adjusted with it and the clutch kept burning. I was going to put my stock one back in, but when I went to install it, I noticed that the fingers (I don't know what they are called) that hold it to the pivot ball are stretched. So it just falls off when I try to bolt up my scattershield. Is this going to be a problem once everything is back together? Is it going to move around? I thought this would be a problem so I ordered a new stock replacement from D&D. But the one I got has the opposite problem. The fingers for the pivot ball are nice and tight, but the ones for the throwout bearing are too low and it easily slides around. Also, the opening where the throwout bearing is a little larger and you can rotate the TOB all the way around.

What one should I use (if any)? What problems could I have with either one? I don't want to take this apart again because the scattershield is a project to get off with all those bolts.

Thanks.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Mar 15, 2008
#2
  • Mar 15, 2008
  • #2
i think the stock one will work fine. all of the forks i have ver seen the "pivotball" had some play in it. but once you put the cable on and put pressure to it it sure's up.
 

5.0 Nostalgia

10 Year Member
Feb 28, 2003
904
5
39
CT
Mar 16, 2008
#3
  • Mar 16, 2008
  • #3
Thanks for the info. I was thinking that once it was tightened, it would be fine because it seems like it won't really move once inside the pocket for the pivot ball. What about using the one from D&D with the larger opening? I am assuming that notch on the throwout bearing it supposed to keep it in place, so it would be more of a problem than using my old stock fork.

Here are some pictures:

Notch on TOB:

View attachment 326580

TOB fitting into stock fork. With the replacement from D&D, The fingers are pushed down, causing the TOB to fit very loosely. Also, the opening is too big and the notch won't hit the opening in the fork. Therefore, the TOB can be completely rotated instead of being locked in place.

View attachment 326581

This is hard to see, but a picture of the fingers stretched out:

View attachment 326582

Thanks again.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Mar 17, 2008
#4
  • Mar 17, 2008
  • #4
The TOB shouldn't rotate, give D&D a call and talk with those guys they are great! I've tweaked the fingers back to get some slop out of stock ones, they bend easily when taken apart if your not careful.
 

5.0 Nostalgia

10 Year Member
Feb 28, 2003
904
5
39
CT
Mar 18, 2008
#5
  • Mar 18, 2008
  • #5
Thanks for the additional info Rick. What would you suggest I use to bend it back into place? If I try to push them down with my fingers, they just pop back into place. Maybe a pliers or something?
 
You must log in or register to reply here.

Similar threads

N
Vibration after new clutch
  • nipple_looker
  • Sep 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
23
Views
723
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 26, 2026
fasterthangas
F
4
Drivetrain Wilwood Clutch and Brake Pedal Combo Installation - Help
  • 427stang
  • Jul 8, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
127
Fox 5.0 Mustang Tech Jul 8, 2026
427stang
4
Drivetrain Broken clutch cable- what it looks like
  • JulianR
  • Aug 6, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
887
Fox 5.0 Mustang Tech Aug 10, 2026
gkomo
T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
326
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
713
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?