• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

clutch problems

  • Thread starter Thread starter jssblues
  • Start date Start date Jul 23, 2008
J

jssblues

New Member
Jul 19, 2008
31
0
0
Jul 23, 2008
#1
  • Jul 23, 2008
  • #1
just put my fresh rebuilt motor back in with the same trany and clutch but now the clutch feels to tight.... i know it is at least kind of disengaging the clutch but not all the way, it just doesnt slide into gear like it used to.....
any help would be greatly appreciated
 
J

jssblues

New Member
Jul 19, 2008
31
0
0
Jul 23, 2008
#2
  • Jul 23, 2008
  • #2
by the way i know about how to adjust it but that is not the issue
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jul 23, 2008
#3
  • Jul 23, 2008
  • #3
How do you know it's not an adjustment issue?

To me, a tight clutch is one with preload. This makes for very quick disengagement. You note that yours is tight but doesnt seem to disengage all the way. Is that correct?

How was the car shifting before the R/R?
How old is the cable?
Do you have a stock quadrant/pawl or aftermarket?
Have you tried adding preload to see what happens to your Point of engagement?


A little info about your trans, clutch and clutch linkage would have been helpful.

Good luck.
 
J

jssblues

New Member
Jul 19, 2008
31
0
0
Jul 23, 2008
#4
  • Jul 23, 2008
  • #4
tranny shifte fine before, stock clutch i believe,cable is fairly new but had to reroute it due to installing long tubes, stock quadrant
 
J

jssblues

New Member
Jul 19, 2008
31
0
0
Jul 23, 2008
#5
  • Jul 23, 2008
  • #5
i have not even fired up the motor yet so i dont know for sure how the clutch will act, but i know it feels tighter that before
 
A

anb0806

New Member
Feb 3, 2009
2
0
0
Feb 3, 2009
#6
  • Feb 3, 2009
  • #6
I am having the same problems with my clutch. We just finished putting in a new shortblock on my 06 Mustang. Did have to change the flywheel due to the bolt pattern on the new crank being an 8 bolt and the stock was a 6 bolt. The car runs great, but when you go to put the car in gear it is very hard to shift and the clutch seems like it does not want to disengage. Could this be a problem with the pilot bearing? The transmission has not been touched and the clutch is stock. There were no problems with any of this when we changed the shortblock. Please help!!!
 

Wallzy

New Member
Aug 20, 2006
128
0
0
Orlando, FL
Feb 3, 2009
#7
  • Feb 3, 2009
  • #7
Check your routing for pinches or sharp bends and make sure that your cable is not binding. Also look at the throw underneath the car to see if you are getting your full throw on your trans.

Walz
 
A

anb0806

New Member
Feb 3, 2009
2
0
0
Feb 3, 2009
#8
  • Feb 3, 2009
  • #8
We checked the throw and it appears that it is getting a full throw. Any other suggestions?
 
You must log in or register to reply here.

Similar threads

F
Engine 1988 Foxbody idle issues
  • fernandosgarage55
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
26
Views
1K
Fox 5.0 Mustang Tech Apr 30, 2026
AeroCoupe
N
Vibration after new clutch
  • nipple_looker
  • Sep 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
23
Views
703
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 26, 2026
fasterthangas
F
L
2006 mustang gt has high clutch bite
  • leevikisley
  • Feb 22, 2026
  • 2005 - 2009 Specific Tech
Replies
0
Views
284
2005 - 2009 Specific Tech Feb 22, 2026
leevikisley
L
T5 5th gear 89 gt
  • mac_55
  • Mar 19, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
273
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 20, 2026
Mustang5L5
Engine Are These rings OK?
  • PonyGTrider
  • Sep 21, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
336
Fox 5.0 Mustang Tech Sep 26, 2026
PonyGTrider
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?