• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

clutch replacement checklist

  • Thread starter Thread starter mustanghunter50
  • Start date Start date Apr 3, 2007

mustanghunter50

New Member
May 30, 2006
123
0
0
easton pa
Apr 3, 2007
#1
  • Apr 3, 2007
  • #1
what all do i need to do when i am puttin my clutch in? are there certain things i need to be aware of? also, what's the easiest way, to drop the tranny or just slide it back?
 

whtpny

New Member
Dec 8, 2002
338
0
0
Spokane WA.
Apr 3, 2007
#2
  • Apr 3, 2007
  • #2
Dropping it or sliding back doesn't matter as long as you have the room you need. Make sure you get everything you need all at once. Pilot bearing also. Alignment tool ( I have done clutches without one but it depends on experience too ). If you plan on doing the job in one day make sure your machine shop can take your flywheel to get it turned. Throwout bearing also. I know lots of people switch the input shaft sleeve on the t-5 as well due to wear issues.
Have fun and be patient if it is your first clutch.
 

Quikstang

Founding Member
Mar 9, 2000
846
0
0
Orlando FL
Apr 3, 2007
#3
  • Apr 3, 2007
  • #3
Yea, not much to a clutch install, just be patient. the easy stuff will always go harder than it should. put a jack under the tail shaft of the tranny after you unbolt the crossmember,its easier to take the tranny and the bellhousing off seperately , once the tranny is out, you'll be able to get all the bolts for the bellhousing off.. If its your first one, remember the starter has to come out too.. Lol, It took me a while to figure that out , the first time I did mine..
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Apr 3, 2007
#4
  • Apr 3, 2007
  • #4
5Spd GT and JRichker have both done write-ups as I recall. Just in case one is searching, I'd keep an eye peeled.

Good luck.
 

mustanghunter50

New Member
May 30, 2006
123
0
0
easton pa
Apr 3, 2007
#5
  • Apr 3, 2007
  • #5
does the fact that i have a tremec make any difference in anything whatsoever?
 
You must log in or register to reply here.

Similar threads

N
Vibration after new clutch
  • nipple_looker
  • Sep 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
23
Views
752
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 26, 2026
fasterthangas
F
Drivetrain Broken clutch cable- what it looks like
  • JulianR
  • Aug 6, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
900
Fox 5.0 Mustang Tech Aug 10, 2026
gkomo
Electrical Lincoln Mark VIII Replacement Fan Motor
  • AeroCoupe
  • Sep 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
174
Fox 5.0 Mustang Tech Sep 26, 2026
AeroCoupe
T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
343
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
T
Vibrating clutch pedal
  • t.hite10
  • Aug 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
8
Views
291
1996 - 2004 SN95 Mustang -General/Talk- Aug 11, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?