Cobra tail pipe question.

johnt785 · Mar 1, 2004

Are the 87-93 Cobra tail pipes the same as the LX 2.5'' chrome tail pipes?

Rick 91GT · Mar 1, 2004

nope...

The Cobra bumper cover require a slightly longer hanger then an LX to fit correctly

Jesseswhite87GT · Mar 1, 2004

Rick 91GT said:
nope...

The Cobra bumper cover require a slightly longer hanger then an LX to fit correctly

So what are the tailpipes that you are supposed to use for the cobra cover? Ive had people on here tell me that the MAC and Flowmaster LX tailpipes are what your suppsed to use?

Mavrick · Mar 1, 2004

LX tails fit fine with the cobra rear bumper..

Im thinking Rick91GT knows what he's talking about.. but the hanger length must be relatively the same length?

QUICK91LX · Mar 1, 2004

i bought my mac cat back for my 89 (RIP) from a guy who said the tails were too short to clear his 93 cobra rear bumper cover... idk if thats how they all are or if it was an install glitch...

Rick 91GT · Mar 1, 2004

Well we put a MAC set-up on our 93 Cobra and found out how they didn't fit...MAC said they would though..lol

We sent MAC the schematics for the correct length of the hanger so they could make a set-up to fit properly, they thanked us and told us they would fix the issue. Howeverwe have seen anything advertised, and that was over 4 years ago.....

I had to make custom hangers to located the pipes correct on my 91GT when I installed a Cobra bumper using the MAC 2.5" LX chrome tail pipe cat back, that I bought 2 years ago.

johnt785 · Mar 2, 2004

So if i go with the Cobra rear bumper for my 90 GT. I can buy the 2.5'' chrome lx tails? I'll just need to make a custom hanger to hold the pipes up?

Rick 91GT · Mar 2, 2004

johnt785 said:
So if i go with the Cobra rear bumper for my 90 GT. I can buy the 2.5'' chrome lx tails? I'll just need to make a custom hanger to hold the pipes up?

Yes, you need to lower the pipes around 1.5" if I remember correctly.

ponyboy19 · Mar 2, 2004

Rick91gt is correct.. I have a set of dynomax 2.5 tail pipes I tried to install yesterday on my 92 with the cobra bumper.. the hangers are too short and with the flowmasters i will actually have to cut the flowtubes to move the mufflers back and inch or two in order to keep the ends of the pipes from hanging out past the bumper and inch and a half. I'm now thinking of just keeping the turn downs as it's more of a PITA than it's worth to me. Might be better though if you use a complete kit unlike i did.

NO_RICE · Mar 2, 2004

take it to an exhuast shop, because no matter what tailpipes you buy they won't fit, especially the flowmaster kit. The pipes wil have to be lengthened (or shortened) and moved down. I got the flowmaster kit, and had some 3" chrome tips put on it. Make sure that the pipes are not too close to the bumper because they will melt the paint.

Rick 91GT · Mar 2, 2004

My MAC fit great as far as length, just came to the edge of the bumper, but as I stated you will need to make custom drop mounts/hangers to get the height. One thing good about the MAC is the ball and socket fitting the tails connect to right after the axles, this give you a lot of adjustment the other systems don't...side to side and up and down.

Stang951 · Mar 3, 2004

I was able to use the stock LX pipes on mine with a longer rubber isolater on the rear hangers. I think I used one from a Subaru. It lowered the tails and did not adversely affect the rest of the exhaust.

johnt785 · Mar 3, 2004

Thanks for the tips!

SilverBullit · Mar 4, 2004

how much do the mac tailpipes run? Are they chrome or polished?

Cobra tail pipe question.

johnt785

Member

Rick 91GT

Mustang Master

Jesseswhite87GT

New Member

Mavrick

QUICK91LX

Rick 91GT

Mustang Master

johnt785

Member

Rick 91GT

Mustang Master

ponyboy19

NO_RICE

Rick 91GT

Mustang Master

Stang951

johnt785

Member

SilverBullit

Similar threads

Cobra tail pipe question.

Member

Mustang Master

New Member

Mustang Master

Member

Mustang Master

Mustang Master

Member

Similar threads

Privacy & Transparency

Privacy & Transparency