• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

comp cams upper intake?

  • Thread starter Thread starter jmd2914
  • Start date Start date Oct 27, 2005
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Oct 27, 2005
#1
  • Oct 27, 2005
  • #1
just curious what you guys thought of it, i was thinking about getting one of these and having my stock lower ported. any suggestions?
 
I

IntenseBlue

Member
Jul 10, 2005
946
0
16
Oct 29, 2005
#2
  • Oct 29, 2005
  • #2
With stock heads and intake it won't perform very well. I'd get the stock lower ported by itsself for now.
 

1EVIL88VERT

New Member
Jul 12, 2004
314
0
0
Dyess AFB, TX
Oct 29, 2005
#3
  • Oct 29, 2005
  • #3
I had one on mine when it was still all stock....it did pull harder, but you will lose alot of low end.....also on a strange note, the comp cams intake makes some really odd sounds at wide open throttle ( kinda like a low moan )...If you can get one cheap and plan on more upgrades later (like a blower) i say get it. I got mine off e-bay for 100.00 and wish i hadn't sold it. Like the other guy said i would port your lower first.
 

Paul Perreca

New Member
Mar 30, 2005
1,085
0
0
Oct 29, 2005
#4
  • Oct 29, 2005
  • #4
i seen it in a jegs mag, its cheap bran new - can't remember exactly how much - but in the mag it says it adds i tihnk 20 horsepower - but adds it up top, and takes it from the bottomend
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Oct 29, 2005
#5
  • Oct 29, 2005
  • #5
You will lose some bottom end. I ran the comp box upper with stock heads and a Cobra lower for a few months before going 351w. The loss of low end was almost intolerable. Power was pathetic under 3500-4000rpm. I would recommend the Cobra lower with this intake as opposed to the stock intake configuration.
The comp cam box intake will allow more engine noise to be audible as there is less mass in the intake to muffle noise. I would not recommend this intake for boost however. It is difficult to get the intake to seal properly, especially where the top and bottom of the box intake bolt together and also where the vac fittings thread into the intake. Also, care must be taken when bolting the intake together, as the polymer material could crack if over-torqued.

In all I think very highly of this intake. I think it is a great value, just be aware of the tradeoffs.

:Word:
jason
 
You must log in or register to reply here.

Similar threads

K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
480
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
D
N/A build on fresh stock 302
  • djcarrot
  • Oct 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
443
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 19, 2026
AeroCoupe
D
Engine HO cam in non HO roller block ‘93 f150
  • DanC1993f150
  • Mar 21, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
522
Fox 5.0 Mustang Tech Mar 29, 2026
General karthief
Engine Hiccup at full throttle
  • keel
  • Jun 2, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
31
Views
1K
Fox 5.0 Mustang Tech Jul 30, 2026
keel
Suspension Harsh Ride
  • PonyGTrider
  • Mar 20, 2026
  • Fox 5.0 Mustang Tech
  • 2 3 4
Replies
62
Views
3K
Fox 5.0 Mustang Tech Apr 11, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?