• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Control Arm Problems- Granatelli

  • Thread starter Thread starter Mustang78
  • Start date Start date Jun 21, 2007

Mustang78

New Member
Feb 8, 2006
486
0
0
Aberdeen, WA
Jun 21, 2007
#1
  • Jun 21, 2007
  • #1
i bought the adjustable upper and lower ocntrol arms used from a guy with an 01 mach 1(do they have a panhard bar stock?), since both upper and lower have heim joints, what will keep the axle from swaying side to side?!?!? here's a picture of the upper's:


And here is the lower's, can anybody explain what will keep the axle in position?


~Mark~
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jun 21, 2007
#2
  • Jun 21, 2007
  • #2
The heim joints self center the rear, you still have the rubber/poly bushings to hold the rear centered at the front mounting points. The spacers hold it in place. Just make sure you grease them well when you install them.

Pull out the threaded portions on the rear and antiseize them very well or they will bind up and you'll never be able to adjust the ride height.
 

Mustang78

New Member
Feb 8, 2006
486
0
0
Aberdeen, WA
Jun 21, 2007
#3
  • Jun 21, 2007
  • #3
so the lower arms keep the axle from going side to side? i think the ones i have are a slightly different versiona nd have the heim joints on the lower control arms too..if all 4 heim joints swivel then the rear end will shift..right? i'll check em out after work tonight, and does anyone know if an 01 mach 1(or any 94-04) mustang has a panhard bar from the factory?

~Mark~
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jun 21, 2007
#4
  • Jun 21, 2007
  • #4
Heim joints on both ends will be alittle noisy but they work just fine, just make sure they are nice and tight and articulate well.

Mach 1 did not have a Panhard bar stock
 
You must log in or register to reply here.

Similar threads

New Products From J&M Products - 1979-1998 & 1999-2004 Race/Extreme Duty Rear Lower Control Arms
  • J&M Products
  • Oct 9, 2025
  • Vendor Sponsor Forums
Replies
0
Views
475
Vendor Sponsor Forums Oct 9, 2025
J&M Products
Tightening upper control arm bushings at ride height dilemma… need some help
  • AnthonyA1234
  • Dec 27, 2024
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
51
Views
7K
Fox 5.0 Mustang Tech Feb 27, 2025
General karthief
Fox Alignment Suggestions
  • PonyGTrider
  • Jul 12, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
633
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 13, 2025
PonyGTrider
Suspension Foxbody ride height change after installing new control arms
  • Mhalc1
  • Jan 3, 2024
  • Fox 5.0 Mustang Tech
  • 2
Replies
36
Views
10K
Fox 5.0 Mustang Tech May 10, 2024
Mhalc1
C
1965 Mustang Lower Control Arm Question.
  • chopper1876
  • Nov 9, 2024
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
19
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Dec 7, 2024
GOvert
G
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?