• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Custom H pipe question, need experienced advice

  • Thread starter Thread starter 85_SS_302_Coupe
  • Start date Start date Dec 9, 2008

85_SS_302_Coupe

it sucks (I know) to be on the receiving end
15 Year Member
Nov 11, 2003
6,945
1,598
223
Northern KY
Dec 9, 2008
#1
  • Dec 9, 2008
  • #1
My buddy has an S10 that currently has straight pipes on it and we're looking to make a crossover pipe for it (basically an H pipe). What i'm curious about is, does it matter how long that crossover pipe is? On most Mustang H pipes you see, the pipes come together and the " - " in the middle is only 6 inches long or so....with his, the pipes come straight off the headers so that crossover will be at least as wide as the headers are, which i figure is at least a foot and a half wide. We're trying to be as cheap cost wise as possible so we're trying to avoid getting into mandrel bends and making it all by scratch..we just wanna weld in a crossover and go but we're unsure if it'll be ok being that long.
 

bynummustang

Seen my other Jackstand?
Jul 24, 2005
1
2
69
NC State University
Dec 9, 2008
#2
  • Dec 9, 2008
  • #2
Sounds about right. Can you just get the dimensions from a BBK site or something? I don't know if it being a certain distance from the headers makes a difference.
 

85_SS_302_Coupe

it sucks (I know) to be on the receiving end
15 Year Member
Nov 11, 2003
6,945
1,598
223
Northern KY
Dec 9, 2008
#3
  • Dec 9, 2008
  • #3
I just wanna cut and weld a straight cross over between what he has now...nice and easy. I just wonder if the length of the crossover makes a difference.
 
P

phutch11

Member
Nov 14, 2005
328
2
18
Dec 9, 2008
#4
  • Dec 9, 2008
  • #4
Supposedly the length of the H-pipe is not terribly important, what is important is the distance of the H pipe from the engine. "Experts" say to take a crayon and make a mark from where the exhaust bolts to the headers down the exhaust pipe towards the mufflers and then run the car.

Where the crayon mark stops melting is where you should weld in the crossover.

Good luck
 

85_SS_302_Coupe

it sucks (I know) to be on the receiving end
15 Year Member
Nov 11, 2003
6,945
1,598
223
Northern KY
Dec 10, 2008
#5
  • Dec 10, 2008
  • #5
phutch11 said:
Supposedly the length of the H-pipe is not terribly important, what is important is the distance of the H pipe from the engine. "Experts" say to take a crayon and make a mark from where the exhaust bolts to the headers down the exhaust pipe towards the mufflers and then run the car.

Where the crayon mark stops melting is where you should weld in the crossover.

Good luck
Click to expand...


Yeah i've heard of doing this trick, but with grease instead of crayon, and for making collectors off the end of headers but i can see where it would make the same sense with the crossover.
 

cenok is family

15 Year Member
Jun 25, 2003
1,409
69
79
Norman, Ok
Dec 10, 2008
#6
  • Dec 10, 2008
  • #6
length shouldn't matter. if you look at most H pipes for 60's GM's, the cross over is over a foot long
 

NIKwoaC

中國製造
15 Year Member
Oct 31, 2006
5,525
943
214
Chengdu Province
Dec 10, 2008
#7
  • Dec 10, 2008
  • #7
You want it as short as possible, for the same concept that makes X pipes work so well. You want the exhaust pulse to travel as short as possible a distance to relieve the pressure differences. Of course, any crossover is better than none.
 
You must log in or register to reply here.

Similar threads

Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
613
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
S
Engine Stalls when downshifting/coasting
  • Scott_S
  • Nov 5, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
902
Fox 5.0 Mustang Tech Nov 6, 2025
Mustang5L5
5
Hello Everyone !
  • 5150K
  • Jul 3, 2026
  • The Welcome Wagon
Replies
0
Views
185
The Welcome Wagon Jul 3, 2026
5150K
5
Progress Thread Progress Thread- From6to8's 95 GT/Saleen Supercharged 331 install
  • from6to8
  • Mar 22, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
27
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 28, 2026
from6to8
M
Engine Intermittent CEL with loss of power
  • Mikebro
  • Sep 7, 2024
  • Fox 5.0 Mustang Tech
  • 2
Replies
20
Views
2K
Fox 5.0 Mustang Tech Sep 13, 2024
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?