• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

DC Controller and using the A/C

  • Thread starter Thread starter GreatWhite
  • Start date Start date Jun 16, 2008

GreatWhite

Member
Feb 24, 2006
232
1
17
Fairfield, PA
Jun 16, 2008
#1
  • Jun 16, 2008
  • #1
Hey guys,

Alright, when I first hooked up my controller, I had no A/C so I didn't hook up the blue lead to the compressor so the fan would run anytime the A/C was turned on. It said in the directions to connect it to the "input" wire that goes to the compressor. Does anyone know which wire that is? I see a black wire and a black/yellow wire. Which of those am I supposed to tap into or am I way off?

The car is an '89.

Thanks, CJ
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 16, 2008
#2
  • Jun 16, 2008
  • #2
It goes to the 12 volt intput to the clutch. Should be black/yellow but use your meter real quick to check it.
The other wire going to the clutch is a ground.
 

GreatWhite

Member
Feb 24, 2006
232
1
17
Fairfield, PA
Jun 16, 2008
#3
  • Jun 16, 2008
  • #3
That's what I figured. I was lookin' through the Haynes manual for wiring schematics. Thanks man.

Only problem I had was gettin the fan to start... It didn't want to start spinning when I put the A/C on. I had to give it a little tap to get going... What's the next thing to check, the fan or the alternator? I have a 3G out of a '94 but it doesn't seem to charge as strong as I hear all the time. I think it might be a ground problem.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 16, 2008
#4
  • Jun 16, 2008
  • #4
WHen you bought the fan and had it on the bench (so it is NOT connected electrically), was the blade resistive to being spun when you first spun it lightly?
WHen you bench tested it, was it sluggish to get started?

If this always happens (AC input or not) when wired to the controller, bench test the fan with a fused power source to see if it balks. If not, the fan motor might be seizing, and the huge start-up draw is seen as a short-to-ground by the controller. In such a circumstance, the controller shuts down.

If your battery is remotely charged, the alt is not the issue.
 

GreatWhite

Member
Feb 24, 2006
232
1
17
Fairfield, PA
Jun 16, 2008
#5
  • Jun 16, 2008
  • #5
Most times it starts up just fine. I didn't notice it dragging before I installed it, but I lost a Taurus fan recently before this one because the motor went on it. This one is out of a Lincoln.
 
You must log in or register to reply here.

Similar threads

T
Electrical Brown Connector #31
  • ta66
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
219
Fox 5.0 Mustang Tech Jul 30, 2026
ta66
T
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
482
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
F
Electrical From scratch: alternator wiring
  • fox racer v2
  • Jun 23, 2025
  • Fox 5.0 Mustang Tech
Replies
0
Views
687
Fox 5.0 Mustang Tech Jun 23, 2025
fox racer v2
F
C
Help with manual conversion
  • CPH89LX
  • Aug 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
705
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 27, 2026
2000xp8
J
Shift light
  • Jfriedrich
  • Jun 22, 2025
  • SN95 4.6L Mustang Tech
Replies
1
Views
252
SN95 4.6L Mustang Tech Dec 29, 2025
dirk shorter
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?