• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Distributor & Balancer Install

  • Thread starter Thread starter buckshot1020
  • Start date Start date Feb 21, 2008
B

buckshot1020

New Member
Mar 21, 2006
3
0
0
Feb 21, 2008
#1
  • Feb 21, 2008
  • #1
I have a longblock ready to go in my 89 Notchback. The distributor needs to go in as well as the balancer. Questions:
1)At what point does the balancer go on in the cycle of the engine?
2)Easiest way to get TDC of #1 cylinder?
3)Once I have TDC of the comression stroke on #1, I can just rotate the rotor to the #1 wire and stab it then set timing.. correct?

Thanks people!
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 21, 2008
#2
  • Feb 21, 2008
  • #2
Put the balancer on before you put the engine back in the car. It is much eaiser to get to the balancer bolt with the engine out of the car. The only problem with it out of the car is keeping the crank from turning when you tighten the bolt.

Putting the distributor back in is fairly simple. Pull #1 sparkplug, put your finger in the sparkplug hole, crank the engine until you feel compression. Then line up the TDC mark on the balancer with the pointer on the engine block.

The distributor starts out with the #1 plug wire lined up at about 12:00 with you facing it. Align the rotor to about 11:00, since it will turn clockwise as it slides into place.

Align the distributor rotor up with the #1 position marked on the cap, slide the distributor down into the block, (you may have to wiggle the rotor slightly to get the gear to engage) and then note where the rotor is pointing. If it still lines up with #1 position on the cap, install the clamp and bolt. If not, pull it out and turn 1 tooth forwards or backwards and try again. Put the #1 spark plug back in and tighten it down, put the clamp on the distributor, but don't tighten it too much, as you will have to move the distributor to set the timing. Note that if it doesn't align perfectly with #1 position, you can turn the distributor until it does. The only problem is that if you are too far one way or the other, you can't turn the distributor enough to get the 10-14 degree optimum timing range.

At this point hook up all the wires, get out the timing light and start the engine. Set the timing where your car runs best. Don't forget to disconnect the SPOUT jumper connector when you set the timing, and plug it back in when you finish.

The HO firing order is 1-3-7-2-6-5-4-8.
Non HO firing order is 1-5-4-2-6-3-7-8
 
You must log in or register to reply here.

Similar threads

Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
348
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
397
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
485
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
L
Help with 1986 GT 5 Speed Please
  • Lcasada1999
  • Mar 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
391
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
207
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?