• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Distributor swap question....

  • Thread starter Thread starter Vinnietbird
  • Start date Start date Apr 7, 2006

Vinnietbird

Member
Jun 2, 2005
584
3
19
Apr 7, 2006
#1
  • Apr 7, 2006
  • #1
O.K.,I feel stupid for asking this.What's the best way to swap my distributor without screwing up the timing?I have changed the engine 3 times in my car,but have never had to pull a distributor.I found out today that somewhere down the engine's life,someone swapped the distributor for an odd unit.It has a large round rotor in it instead of the standard rotor I've had in my other cars.I have one from my Thunderbird 5.0 that I pulled to install the current H.O. engine.Thanks.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Apr 7, 2006
#2
  • Apr 7, 2006
  • #2
If you remove the distributor, there is no way you can accurately set the timing without a timing light.

Putting the distributor back in is fairly simple. Pull #1 sparkplug, put your finger in the sparkplug hole, crank the engine until you feel compression. Then line up the TDC mark on the balancer with the pointer on the engine block.

The distributor starts out with the #1 plug wire lined up at about 12:00 with you facing it. Align the rotor to about 11:00, since it will turn clockwise as it slides into place.

Align the distributor rotor up with the #1 position marked on the cap, slide the distributor down into the block, (you may have to wiggle the rotor slightly to get the gear to engage) and then note where the rotor is pointing. If it still lines up with #1 position on the cap, install the clamp and bolt. If not, pull it out and turn 1 tooth forwards or backwards and try again. Put the #1 spark plug back in and tighten it down, put the clamp on the distributor, but don't tighten it too much, as you will have to move the distributor to set the timing. Note that if it doesn't align perfectly with #1 position, you can turn the distributor until it does. The only problem is that if you are too far one way or the other, you can't turn the distributor enough to get the 10-14 degree optimum timing range.

At this point hook up all the wires, get out the timing light and start the engine. Set the timing where your car runs best. Don't forget to disconnect the SPOUT jumper connector when you set the timing, and plug it back in when you finish.
 

Vinnietbird

Member
Jun 2, 2005
584
3
19
Apr 7, 2006
#3
  • Apr 7, 2006
  • #3
Thanks a lot.I'm on it.I appreciate all the help here.You guys have been great.
 
You must log in or register to reply here.

Similar threads

F
Electrical Foxbody wiring harness 2.3 to v8 swap
  • Foxbodyjake
  • Mar 23, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
26
Views
1K
Fox 5.0 Mustang Tech Sep 7, 2026
Kleinjj27
K
P
Engine Swapping EFI distributor for carb distributor- shaft length is different
  • pindude80
  • Jul 20, 2024
  • Fox 5.0 Mustang Tech
Replies
2
Views
1K
Fox 5.0 Mustang Tech Jul 21, 2024
pindude80
P
8
87 lx 4cyl to v8 project 4 lug disc conversion questions
  • 87lx428
  • Mar 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
635
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 25, 2026
87lx428
8
D
Engine 85 GT Backfires through Carb
  • DienstXIV
  • Oct 3, 2025
  • Fox 5.0 Mustang Tech
Replies
19
Views
1K
Fox 5.0 Mustang Tech Oct 7, 2025
85GTStangGuy
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
491
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?