• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Double Check Everything

  • Thread starter Thread starter kpack5982
  • Start date Start date Feb 16, 2006

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Feb 16, 2006
#1
  • Feb 16, 2006
  • #1
Alright, so just checked the tracking and my new gt40 ported lower and explorer upper will be here tomorrow er today now I guess, so begins my 3 day weekend, starting with the new intake. Here's a list of what I'm pickin up tomorrow night, so let me know if there is anything missing:

Some Blue Silicone Sealant
A couple injector install kits just in case
Some anti-seize stuff
New Razor blade scraper
Fuel line tools, 1/2 and 5/8" ones
Upper manifold gasket
Felpro 1250 for lower gasket
short formed hose between thermostat housing and intake
6 ft 7/64 or 1/8" vac hose
2 ft 1/2" heater hose
1 & 1/2 ft 1/2" heater hose
4 x 3/4" hose clamps
4 x 1/2" hose clamps

Now for a few questions:

1) What upper manifold gasket do I need to get a gt40 one, explorer, or cobra one? Does it matter, are they the same, is one cheaper than another?

2) Can I reuse the stock bolts for the t/b and egr plate, since I'm keeping the stock t/b for now ( just until I decide what aftermarket one to get) I believe they are 5/16 - 18 x 4 & 1/2" long, four of them

3) Are the fuel line tools a must? I read somewhere that someone did without. How much do they run?

4) Does the act have a port on the gt-40 lower? Or is it a case by case basis?

5) A 1" Phenolic spacer is coming with them, does anyone have any experience with it on their cars fitting, with for instance stock mounts? Also I take it I'll need 2 of the upper manifold gaskets for the spacer?

6) Does the upper manifold gasket have t/b gasket with it by chance?

AND LAST OF ALL

7) Can i reuse the lower manifold studs?

It's amazing how much of this I got from you guys, but just want to be very concise so I have everything together and prepared for when I do this. Thanks in advance to whoever even gets through this post, let alone respond to any of the questions. Thanks guys
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 16, 2006
#2
  • Feb 16, 2006
  • #2
1.) The Explorer upper gasket will fit fine.

2.) You can reuse all the old bolts, the problem is they may be very corroded. Home Depot or Ace Hardware can supply you with new bolts.

3.) Any of the auto parts stores will have the fuel line tools. Advance Auto Parts definitely has them. Cost is about $10.

4.) The ACT may or may not have a place drilled for it. I have a tech note on how to relocate it to the stock airbox in a very neat and clean manner.

5.) Two gaskets will be needed if you use a spacer between the uppler & lower manifolds.

6.) The T/B gaskets are a separate item unless you buy a gasket kit. Even then, you need to check before you leave the auto parts store.

7.) All the lower manifold mount bolts & studs are reuseable.

FYI, here's the ACT relocation tech note:

The ACT (Air Charge Temp) sensor will probably need to be moved. The GT 40 lower manifold isn't drilled & tapped for it to go into the intake like the stock manifold was. There is a boss cast into the GT 40, but a machine shop will have to drill & tap the new manifold. The best spot for the ACT is the air box if you don't do the drill and tap thing. You get to cut and splice the 2 ACT wires in order to make them long enough to reach the air box. Solder the wire extensions on the existing wires & use heat shrink tubing to cover the splices. Offset the place where you cut the wires so that you don't have a big bulge when you put heat shrink over the 2 wires to cover & protect them. The air box gets a hole (5/8" or so) for the ACT drilled about 1 1/4" down & 1/1/4" in on the front top side near the upper radiator hose. A brass fitting nut from Home Depot or Ace Hardware secures the ACT into the air box.

If you are very clever, you will find that the ACT connector comes apart so that you can remove the pins. A very small screwdriver releases the lock in the front of the center insert, while another small screwdriver inserted in the back pushes it out. Once the center insert is out of the connector shell, the pins come out easily. New pins are available from AutoZone in a $5 electrical pin kit for Fords. Crimping the pins on the extender wires saves you from having to splice them twice: once to put the connector on and once to extend the wires.

6 ft black 18 gauge wire
6 ft green 18 gauge wire
6 ft 1/4" heat shrink tubing
1 ft 3/16" heat shrink tubing

Measure the 2 extender wires & cut them to length, crimp one set of pins on them. Then mate up the extender pins with the wiring harness & slide the 3/16" heat shrink tubing over them & shrink the tubing. Then slide the 1/4" heat shrink tubing over the pair of wires and shrink the tubing. When you are done you'll have about 1" of wire left without heat shrink tubing on it to strip & crimp the new pins on. Stick the new pins in the old connector shell, assemble it and you are done. It looks as good as factory. Some wire loom can be used to enhance the "Factory Look".
 

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Feb 16, 2006
#3
  • Feb 16, 2006
  • #3
Problem with the relocation of the act is that I have a cai, i'd hate to mess with that, but I suppose I could drill that out. May be easier just to drill and take the lower there.
 
You must log in or register to reply here.

Similar threads

Engine Heater hose restrictor purpose
  • Mcmahst
  • May 5, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
1K
Fox 5.0 Mustang Tech May 11, 2025
limp
K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
399
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
H
Engine 1987 5.0 HO vacuum hose locations
  • harryhaber
  • Jun 20, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
633
Fox 5.0 Mustang Tech Jun 21, 2025
limp
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
487
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
S
Fox Another try for the European guy to get his first Fox
  • Schargedfox
  • Aug 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
395
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 4, 2026
DadLife0724
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?