Alright, so just checked the tracking and my new gt40 ported lower and explorer upper will be here tomorrow er today now I guess, so begins my 3 day weekend, starting with the new intake. Here's a list of what I'm pickin up tomorrow night, so let me know if there is anything missing:
Some Blue Silicone Sealant
A couple injector install kits just in case
Some anti-seize stuff
New Razor blade scraper
Fuel line tools, 1/2 and 5/8" ones
Upper manifold gasket
Felpro 1250 for lower gasket
short formed hose between thermostat housing and intake
6 ft 7/64 or 1/8" vac hose
2 ft 1/2" heater hose
1 & 1/2 ft 1/2" heater hose
4 x 3/4" hose clamps
4 x 1/2" hose clamps
Now for a few questions:
1) What upper manifold gasket do I need to get a gt40 one, explorer, or cobra one? Does it matter, are they the same, is one cheaper than another?
2) Can I reuse the stock bolts for the t/b and egr plate, since I'm keeping the stock t/b for now ( just until I decide what aftermarket one to get) I believe they are 5/16 - 18 x 4 & 1/2" long, four of them
3) Are the fuel line tools a must? I read somewhere that someone did without. How much do they run?
4) Does the act have a port on the gt-40 lower? Or is it a case by case basis?
5) A 1" Phenolic spacer is coming with them, does anyone have any experience with it on their cars fitting, with for instance stock mounts? Also I take it I'll need 2 of the upper manifold gaskets for the spacer?
6) Does the upper manifold gasket have t/b gasket with it by chance?
AND LAST OF ALL
7) Can i reuse the lower manifold studs?
It's amazing how much of this I got from you guys, but just want to be very concise so I have everything together and prepared for when I do this. Thanks in advance to whoever even gets through this post, let alone respond to any of the questions. Thanks guys
Some Blue Silicone Sealant
A couple injector install kits just in case
Some anti-seize stuff
New Razor blade scraper
Fuel line tools, 1/2 and 5/8" ones
Upper manifold gasket
Felpro 1250 for lower gasket
short formed hose between thermostat housing and intake
6 ft 7/64 or 1/8" vac hose
2 ft 1/2" heater hose
1 & 1/2 ft 1/2" heater hose
4 x 3/4" hose clamps
4 x 1/2" hose clamps
Now for a few questions:
1) What upper manifold gasket do I need to get a gt40 one, explorer, or cobra one? Does it matter, are they the same, is one cheaper than another?
2) Can I reuse the stock bolts for the t/b and egr plate, since I'm keeping the stock t/b for now ( just until I decide what aftermarket one to get) I believe they are 5/16 - 18 x 4 & 1/2" long, four of them
3) Are the fuel line tools a must? I read somewhere that someone did without. How much do they run?
4) Does the act have a port on the gt-40 lower? Or is it a case by case basis?
5) A 1" Phenolic spacer is coming with them, does anyone have any experience with it on their cars fitting, with for instance stock mounts? Also I take it I'll need 2 of the upper manifold gaskets for the spacer?
6) Does the upper manifold gasket have t/b gasket with it by chance?
AND LAST OF ALL
7) Can i reuse the lower manifold studs?
It's amazing how much of this I got from you guys, but just want to be very concise so I have everything together and prepared for when I do this. Thanks in advance to whoever even gets through this post, let alone respond to any of the questions. Thanks guys