Edelbrock RPM heads or?

$uperstang

New Member
Jul 20, 2004
476
1
0
Detroit, MI
Ok guys,

I am looking at purchasing heads for my combo. It will be a 331 stroker with 10PSI from the Vortech blower. I am looking at EDL-60259 w/ 2.02/1.60 that flow 170cc. Or what do you guys think about AFR 185's or Edelbrock Victor Jr. that are 2.05/1.60?

Please help I had to get rid of the trick flows because of the SRP pistons not clearing?


I am leaning toward Edelbrock 60259's
 
I believe the 185's flow better than the Edelbrock's. Also you can get the 185's with 62cc chambers to reduce the compression a little. If the car has to pass emissions the victor' jr's do not have a EGR passage for the ford small block.
Hope that helps. :)
 
CrazyCobra said:
I believe the 185's flow better than the Edelbrock's. Also you can get the 185's with 62cc chambers to reduce the compression a little. If the car has to pass emissions the victor' jr's do not have a EGR passage for the ford small block.
Hope that helps. :)

I know the AFR's flow better but considering the RPM performers which are 60cc is it really worth the extra $300 to get the AFRs? No need for Smog stuff here in Michigan.
 
Either head will be fine..I like the 300 to put towards other things. The $$ difference was a deciding factor in my choice of the Eddy heads, with the saved cash I paid for my cam.
 
Looking at your sig, I see that you are already running twisted wedge heads. Why are you switching? I don't think the flow numbers are much better on the edel's than on the TW. If getting the most out of your combo is what you are after than the 185's or the victor jr's are the way to go. Because these two heads flow more it will increase the volumetric eff. of your engine. What this means for your combo is you can make the same power with less boost. Less boost means lower charge temp. Lower charge temp means less chance of detonation. This means you run a safer tune, or you can increase some timing for more power.
Also with the Edel RPM heads, been a while since I've had my valve covers off mine but I believe they have a rather weak single valve spring. So a 2.02 valve with 10 psi boost means lower pressure on the seat, not a good thing. A spring upgrade will be needed. The AFR have upgrade packages available to accommodate this.
Just some things to think about. :)
 
$uperstang said:
That's what I think too, I am going with the 2.02/2.60
Here's some food for thought. Have a little porting done before you put the heads on. Maybe look into a custom cam grind in concert with the porting. Check out Cam Innovations. I believe they are in Michigan. I wish I had done that before I put my motor together. Now I'm thinking about another top end tear down this winter.
 
CrazyCobra said:
Looking at your sig, I see that you are already running twisted wedge heads. Why are you switching? I don't think the flow numbers are much better on the edel's than on the TW. If getting the most out of your combo is what you are after than the 185's or the victor jr's are the way to go. Because these two heads flow more it will increase the volumetric eff. of your engine. What this means for your combo is you can make the same power with less boost. Less boost means lower charge temp. Lower charge temp means less chance of detonation. This means you run a safer tune, or you can increase some timing for more power.
Also with the Edel RPM heads, been a while since I've had my valve covers off mine but I believe they have a rather weak single valve spring. So a 2.02 valve with 10 psi boost means approx 50 to 60 lbs lower pressure on the seat, not a good thing. A spring upgrade will be needed. The AFR have upgrade packages available to accommodate this.
Just some things to think about. :)
I've heard the same thing about the springs on my Edelbrocks. I'm thinking about a 100 shot and I've been told I better go with a stronger spring before I go on the bottle.
 
Fishhawk said:
I've heard the same thing about the springs on my Edelbrocks. I'm thinking about a 100 shot and I've been told I better go with a stronger spring before I go on the bottle.
I can't see why you have to upgraded spring for nitrous :shrug: . Perhaps because of the increased chance of over reving. This could lead to vavle float, which may result in bent push rods etc.
In any case a single valve spring is not a good idea , especially with any size cam, what happens if you break a spring? Bent valve and possibly worse. This is more likly why it has been suggested you upgrade springs before you add power.
 
$uperstang said:
I have the trickflow stage 1 cam 221/225 @.050 .499/.510. I have 1.6 3/8" stud mount rockers and now realized that the Victor jr.'s are 7/16 stud mount, so that will not work.
AFR have 7/16 and 3/8.
I don't mean to ram these heads down your throat, its just that I have done a lot of research and these seem to be at the top of the list. If emmissions is not an issue than have a look at the 205 that head is sick.
Take a look for yourself, see what you think. :nice:
http://www.airflowresearch.com/
BTW i myself am selling my Edel's and have the 185 emission legals on order. :nice:
 
CrazyCobra said:
AFR have 7/16 and 3/8.
I don't mean to ram these heads down your throat, its just that I have done a lot of research and these seem to be at the top of the list. If emmissions is not an issue than have a look at the 205 that head is sick.
Take a look for yourself, see what you think. :nice:
http://www.airflowresearch.com/
BTW i myself am selling my Edel's and have the 185 emission legals on order. :nice:

Don't get me wrong I know the AFR's are better and flow better. But are they worth an extra $300-400 dollars. That is my point with about $9000 worth of partts I am trying to get the most for the money. I know I can use that $300-400 for something more like my Fluidyne radiator that costs $369. :shrug:
 
$uperstang said:
Ok guys,

I am looking at purchasing heads for my combo. It will be a 331 stroker with 10PSI from the Vortech blower. I am looking at EDL-60259 w/ 2.02/1.60 that flow 170cc. Or what do you guys think about AFR 185's or Edelbrock Victor Jr. that are 2.05/1.60?

Please help I had to get rid of the trick flows because of the SRP pistons not clearing?


I am leaning toward Edelbrock 60259's

They don't flow 170 cc......that's the size of the intake ports. They actually flow 245 cfm on the intake side and around 180 cfm on the exhaust side.
 
$uperstang said:
Don't get me wrong I know the AFR's are better and flow better. But are they worth an extra $300-400 dollars. That is my point with about $9000 worth of partts I am trying to get the most for the money. I know I can use that $300-400 for something more like my Fluidyne radiator that costs $369. :shrug:
If it were my car I would not only spend the extra 3-4 hundred I would spend the $180 for the upgrade to severe duty valves and 1.540" springs. However its not mine, so you'll have to decide if its worth it :shrug: . The problem is you'll end up spending more down the road to port the Edel's just to get them as good as the AFR's right out of the box, And you should still upgrade the valve springs on the Edel's.
The choice is easy for me, but what do I know I seem to spend money like a drunkn sailor :) .
 
CrazyCobra said:
If it were my car I would not only spend the extra 3-4 hundred I would spend the $180 for the upgrade to severe duty valves and 1.540" springs. However its not mine, so you'll have to decide if its worth it :shrug: . The problem is you'll end up spending more down the road to port the Edel's just to get them as good as the AFR's right out of the box, And you should still upgrade the valve springs on the Edel's.
The choice is easy for me, but what do I know I seem to spend money like a drunkn sailor :) .

I really depends on what cam you have when upgrading springs. If you have a fairly mild cam there is no need to upgrade the springs. In fact Edelbrock's "power package" has the E303 in it.....so you know for sure the springs are at least good for that. I was seriously debating this for my setup a little while ago. I'll be running the Edelbrock 60229 heads with a Comp Cams XE270HR cam. I checked the recommended springs for that cam and compared them to the Edelbrocks.....they are within 10% of each other, which is considered acceptable. If I get any valve float, I'll be sure to post about it.
 
maverick0716 said:
I really depends on what cam you have when upgrading springs. If you have a fairly mild cam there is no need to upgrade the springs. In fact Edelbrock's "power package" has the E303 in it.....so you know for sure the springs are at least good for that. I was seriously debating this for my setup a little while ago. I'll be running the Edelbrock 60229 heads with a Comp Cams XE270HR cam. I checked the recommended springs for that cam and compared them to the Edelbrocks.....they are within 10% of each other, which is considered acceptable. If I get any valve float, I'll be sure to post about it.
I agree 100%. :nice:
In this case $uperstang is running 10psi of boost, this reduces the effective seat pressure of the spring. I would upgrade in this case.
I run the e cam with Edelbrock 399 heads(same as you no loc wire). In first gear (3.97 4 banger) with 3.73's the car falles on its face at 5200rpm, I haven't nailed it down yet, but its either ignition break down or valve float. This only happens in first and just started this year with 15000kms on engine.
Just a warning, I wish that i had chosen a head for stud mount rockers, now I am replacing my edel's because of the pedestal mount(and AFR's rock :p ).