• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

EGR tube and Mac headers

  • Thread starter Thread starter frcefedlx
  • Start date Start date Oct 6, 2007
F

frcefedlx

New Member
Dec 6, 2004
184
0
0
Oct 6, 2007
#1
  • Oct 6, 2007
  • #1
I bought Mac headers and installed them back when I did my HCI setup and at that time spaced intake 3/8" and bought the extension nut for the egr tube. When it came time to install the tube it would not fit due to Mac locating the fitting on a different header tube than OEM. With the adaptor and the tube put in place on the egr it does not go forward or down enough to complete the connections. I would like to get this hooked up and am curious if there is a setup out there for just this situation or will I need to pay a shop to fabricate a tube. I do not have the means to do any fab work like this.
 

Stanger007

Founding Member
Sep 26, 2001
2,015
2
46
Baton Rouge, LA
Oct 6, 2007
#2
  • Oct 6, 2007
  • #2
I haven't seen anyone selling custom tubes, nor a flexible alternative. Most just cut off their "nuts" (haha) and reuse them on some copper store from the hardware store after flaring/bending it.

I ended up taking my EGR off the car and turning it off in the tune because my tube broke in half and I was too lazy to go through all the trouble.

Who's tuning your car?

Wes
 
F

frcefedlx

New Member
Dec 6, 2004
184
0
0
Oct 6, 2007
#3
  • Oct 6, 2007
  • #3
It seems to run fine right now as it is but I am going to get a chip burned at horsepower ranch as soon as I get all these little issues out of the way. I am also going to put a power pipe and a different pulley on the charger before I get a good solid tune behind it.
 
You must log in or register to reply here.

Similar threads

New Exhaust for 408w stroker
  • SadbutTrue
  • Sep 10, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
1
Views
163
1965 - 1973 Classic Mustangs -General/Talk- Sep 10, 2026
nickyb
A
P0036 P0056 P0137 P0157 2020 Ford Mustang GT
  • AmkoA
  • Jun 16, 2026
  • 2024+ (S650) Mustang -General/Talk
Replies
0
Views
288
2024+ (S650) Mustang -General/Talk Jun 16, 2026
AmkoA
A
Exhaust 1 3/4” Long Tubes on a Fox Body AOD – Easiest route?
  • 5.0 Mike
  • Mar 19, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
2K
Fox 5.0 Mustang Tech Mar 21, 2025
5.0 Mike
R
bbk shorty header to mid pipe gasket
  • randyyy
  • Sep 29, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
503
1996 - 2004 SN95 Mustang -General/Talk- Sep 29, 2025
randyyy
R
F
Ford 460 swap
  • Ford460
  • Sep 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
491
1996 - 2004 SN95 Mustang -General/Talk- Sep 14, 2026
Ford460
F
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?