• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

EGR

  • Thread starter Thread starter raulbadillo
  • Start date Start date Sep 12, 2008
R

raulbadillo

New Member
Aug 26, 2008
51
0
0
Sep 12, 2008
#1
  • Sep 12, 2008
  • #1
Guys any tips on how i can get my stock EGR spacer removed? I got a new one on its way and I need the bolts from my stock intake. I think. Not sure if the one im getting comes with the bolts or not but anyways i still would like to know how to remove the EGR and the bolts from the stock intake. Thanks. :SNSign:
 

93 LX

Founding Member
Jun 2, 2000
3,081
3
0
Norwalk, CA.
Sep 12, 2008
#2
  • Sep 12, 2008
  • #2
loosen the 4 nuts on the throttle body and pull the TB. Loosen the hoses and what not from the EGR spacer, all the plugs and such. Then the spacer will come off. With mine the coolant leaked so one of the studs was bad so it made taking off hard. Have fun but its simple.
 
R

raulbadillo

New Member
Aug 26, 2008
51
0
0
Sep 12, 2008
#3
  • Sep 12, 2008
  • #3
um, i have done the above. It seems like its stuck to the upper plenum. do i need to pound on it? use a chisel? I dont care about the gasket as i got new ones. and what about the studs? any advice on getting them off? I need them for my other intake i have.
 

myslo50

Member
Jun 12, 2006
247
3
18
ohio
Sep 12, 2008
#4
  • Sep 12, 2008
  • #4
i had to hammer mine off, it was a PITA. if u got a new spacer coming than use a chisel and have at it. try using some pb blaster and let it soak. after u get the spacer off DO NOT use a inverted torx socket, i used a pair of vise grips in the center of the stud.........but i would soak the piss out of everything first
 

Boostedpimp

20+ Year Stangneter
May 8, 2003
1,451
493
154
NJ
Sep 13, 2008
#5
  • Sep 13, 2008
  • #5
most likely the studs are rusted.. and causing the egr not to be able to be slid off easy which was the case for. I tried pb blaster and some heat but that still didn't completely work so i ended up hitting and prying it to death to get the egr spacer off because I too needed the studs. Once the egr spacer is off there is a secton of the studs that aren't threaded which was covered by the egr spacer. I used a set of channel locks on that area and twisted them out.. prior to that I used the two nut method on each stud but from all the rust I could only get one out that way. If your not formilar with that method.. you put one nut on all the way then put another one on that same stud and tight it up again the first nut. The stick your wrench on the first nut and try to undo

good luck
 

Maryland Stang

Active Member
Aug 21, 2002
1,656
30
39
Greenville, NC
Sep 13, 2008
#6
  • Sep 13, 2008
  • #6
For Heaven's sake why do people think they need those studs? This has got to be the number 1 biggest problem I've ever seen here. Go to any place that sells bolts and buy new ones. They don't need to be studs.

 
R

raulbadillo

New Member
Aug 26, 2008
51
0
0
Sep 13, 2008
#7
  • Sep 13, 2008
  • #7
how long do they need to be and what thread?
 

Maryland Stang

Active Member
Aug 21, 2002
1,656
30
39
Greenville, NC
Sep 13, 2008
#8
  • Sep 13, 2008
  • #8
5/16"-18 by 3-1/2"
 
You must log in or register to reply here.

Similar threads

Engine Vacc leak detector
  • Creomod
  • Jul 19, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
217
Fox 5.0 Mustang Tech Jul 25, 2026
Mustang5L5
Engine (EGR Deleted) Solution the hotter combustion chambers?
  • PonyGTrider
  • Jan 21, 2026
  • Fox 5.0 Mustang Tech
  • 3 4 5
Replies
97
Views
5K
Fox 5.0 Mustang Tech May 2, 2026
PonyGTrider
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
Resolved 1999 cobra removed lower intake manifold to crossovertube
  • hvcobra99
  • Sep 6, 2026
  • SVT Tech Forum
Replies
0
Views
166
SVT Tech Forum Sep 6, 2026
hvcobra99
Engine Catch Can or not?
  • R82148V
  • Mar 4, 2026
  • Fox 5.0 Mustang Tech
Replies
9
Views
493
Fox 5.0 Mustang Tech Mar 6, 2026
ctandc
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?