• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

elec fan controller setpoint

  • Thread starter Thread starter rockyracoon
  • Start date Start date May 25, 2006
R

rockyracoon

10 Year Member
Nov 23, 2005
874
27
49
margate NJ
May 25, 2006
#1
  • May 25, 2006
  • #1
well I decided to let my controller run the SN 95 in low speed only.the way I have it set it is coming on at 215 deg and going off at 205*,im gonna wire the high side of the fan to a relay and a switch in the cab,and prolly use it when the A/C is on.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 25, 2006
#2
  • May 25, 2006
  • #2
If I read you right, that's not a good idea.

You do NOT want high and load speed engaged at the same time. The fan ends up spinning at a semi fast rate and shortening the life of the motor quite a bit. Also, a decent sized relay should be used for high speed (esp if you ever switch the fan from off to high, which also is not real great for the fan).

There are several ways to get around this issue, but they require more relays and wiring.

If funds allow, a Dc Control unit would be the way to go, all the way around.

Good luck.
 
R

rockyracoon

10 Year Member
Nov 23, 2005
874
27
49
margate NJ
May 25, 2006
#3
  • May 25, 2006
  • #3
OIC.how about the setpoint temp is that too hot to have the fan start? I thought I read in another post that 215* was good.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 26, 2006
#4
  • May 26, 2006
  • #4
rockyracoon said:
OIC.how about the setpoint temp is that too hot to have the fan start? I thought I read in another post that 215* was good.
Click to expand...
What temperature t-stat do you use? It did seem a little hot to me (almost no matter what - even for a stock stat), but I figured you had a reason for that.

If you have a 180, I'd have it come on at about 197-200 and off at 187* or so. This will depend upon your thermostat (some dont open with much precision, nor are they consistant under differing conditions).

Good luck.
 
R

rockyracoon

10 Year Member
Nov 23, 2005
874
27
49
margate NJ
May 26, 2006
#5
  • May 26, 2006
  • #5
im running a 195* stat.Should I have it come on a little lower that 215*?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 26, 2006
#6
  • May 26, 2006
  • #6
rockyracoon said:
im running a 195* stat.Should I have it come on a little lower that 215*?
Click to expand...
You could probably try something like on at 208*, off at 200*. This would be what the factory used for low speed on the 94-95's, and it's about as low as I would go - you dont want to run it down so far that the fan always runs (in case your stat is a little slow to open).

Just MHO.
Good luck.
 
R

rockyracoon

10 Year Member
Nov 23, 2005
874
27
49
margate NJ
May 26, 2006
#7
  • May 26, 2006
  • #7
Ok I just readjusted it and thats pretty much where she is.On at 209* off at like 199*.as I said I just have the low speed of the fan hooked up and the 25 amp inline fuse is fine.when the a/c is on the controller keeps the fan on all the time and the temp just stays at 208-210*.what im gonna do down the road is hook up a 3 way switch inside the car and run one leg to the controller ,which only gives me low speed and hook the other leg up to the high speed wire via a relay for when it gets really hot out and the a A/C is on.That way when I throw the switch it will be out of low for a second but hopefully will keep me from getting the initial amp spike if I started it up in low from the get go.
 
You must log in or register to reply here.

Similar threads

Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
496
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
1
Electrical 1985 mustang gt Led conversion trouble
  • 1985fox
  • Jan 5, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
854
Fox 5.0 Mustang Tech Jan 15, 2026
1985fox
1
D
1999 G/T 4.6 A/C clutch not engaging.
  • David B.
  • Apr 26, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
407
1996 - 2004 SN95 Mustang -General/Talk- May 8, 2025
David B.
D
K
3.8 T5 & Bellhousing to 1987 Lincoln 5.0
  • ks65stang
  • Mar 2, 2026
  • Other Auto Tech
Replies
3
Views
575
Other Auto Tech Mar 3, 2026
Noobz347
1987 Mustang GT Mass Air Conversion Help
  • mustangmike6996
  • Jan 1, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
2K
Fox 5.0 Mustang Tech Feb 4, 2025
mustangmike6996
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?