• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Engine Pull Out And Rebuild

  • Thread starter Thread starter tubbaguts
  • Start date Start date Aug 14, 2017
T

tubbaguts

Member
May 22, 2017
14
3
13
Aug 14, 2017
#1
  • Aug 14, 2017
  • #1
In the spring time I purchased a 91 LX 5.0 that had been sitting for a while but does run and drive. We plan to pull the engine to repair the leaking oil pan gasket in the coming months but I am thinking that while the engine is out this is a great time to make any repair or modifications to the engine. Below is a current list of what the engine has when I bought it.
Stock heads - from what I can tell
Ford Racing B303 cam
Edlebrock Performer 5.0 RPM II intake manifold
BBK 65mm throttle body and spacer
MAC shorty headers
stock injectors (I believe as beige in color)
Under drive pulley
So my question is, what is the best way to tell if I need to tear the whole motor apart or not? It leaks oil but does not seem to burn oil as we have not needed to add oil since last oil change a few months back and we don't have any oil residue at the exhaust. It does have a high end (4k rpm) miss/sputter which leads me to believe I need new injectors. Once I have the oil pan off I can get a visual of the crank and such but obviously would need to take a part the upper half to get to heads and pistons. Would like to get the horsepower up and with the cam/intake it may be possible. Probably need new heads to hit over 300+ horsepower at the wheels. Would like to hear thoughts / opinions / experience on the subject.
 

FoxMustangLvr

I love my Pimp
SN Certified Technician
Oct 14, 2012
4,968
3,514
204
Spokane, Wa
Aug 14, 2017
#2
  • Aug 14, 2017
  • #2
tubbaguts said:
In the spring time I purchased a 91 LX 5.0 that had been sitting for a while but does run and drive. We plan to pull the engine to repair the leaking oil pan gasket in the coming months but I am thinking that while the engine is out this is a great time to make any repair or modifications to the engine. Below is a current list of what the engine has when I bought it.
Stock heads - from what I can tell
Ford Racing B303 cam
Edlebrock Performer 5.0 RPM II intake manifold
BBK 65mm throttle body and spacer
MAC shorty headers
stock injectors (I believe as beige in color)
Under drive pulley
So my question is, what is the best way to tell if I need to tear the whole motor apart or not? It leaks oil but does not seem to burn oil as we have not needed to add oil since last oil change a few months back and we don't have any oil residue at the exhaust. It does have a high end (4k rpm) miss/sputter which leads me to believe I need new injectors. Once I have the oil pan off I can get a visual of the crank and such but obviously would need to take a part the upper half to get to heads and pistons. Would like to get the horsepower up and with the cam/intake it may be possible. Probably need new heads to hit over 300+ horsepower at the wheels. Would like to hear thoughts / opinions / experience on the subject.
Click to expand...
I just had my engine out this past winter doing similar things for the same reasons. My oil pan, valve covers, and rear main seal were all leaking. Cause for leak primarily was a bad PCV. The crank pressure had to place to escape so it blows the seals out. Make sure a new PCV and grommet is part of the plan or you'll be doing this again. B cam sounds cool at idle but there's better out there. What are you goals and purpose for this car? Daily driver to work? Fun toy on the weekends? Drag strip? The cam and other power upgrades will depend on purpose and HP goal. Do you have a manual transmission or automatic?

One more thing, stock 19# injectors are orange, not sure which are gray. The 4k rpm miss could be an electrical issue like distributor or your MAF could be mismatched with your injectors. Another cause could be fuel delivery related or even weak fuel pressure.
 
T

tubbaguts

Member
May 22, 2017
14
3
13
Aug 14, 2017
#3
  • Aug 14, 2017
  • #3
Thanks for the tip on the PVC.
The car is an automatic and the previous owner had it rebuilt, added higher stall speed torque converter (did not remember the rpm) and a shift kit plus 4.10 gears. Our plan is a weekend cruiser, some daily driving around town and the occasional 1/8 mile Friday night drags. Would like to reuse a many of the aftermarket products as we can and we love the idle of the B cam even though have read there are much better cams out there. I believe the MAF was swapped at one point as well as the wires for the sensor have been spliced. I am the third owner but the first two did not do a great job of documenting everything they did.
 

FoxMustangLvr

I love my Pimp
SN Certified Technician
Oct 14, 2012
4,968
3,514
204
Spokane, Wa
Aug 14, 2017
#4
  • Aug 14, 2017
  • #4
Sounds to me that the previous owner (PO) hacked it up a bit. We need to see where we are before you can plan on what to reuse and how to upgrade there. I understand how budgets go and don't expect an unlimited budget from anyone. With a simple B cam and upgraded intake manifold there is no need to increase fuel injector size. The stock 19# injectors and stock fuel pump would do the job just fine for those upgrades. We need to identify what injectors you have and the MAF. You cannot simply upgrade injectors without a properly matching MAF or tuning or it won't run correctly. Remember, fuel upgrades such as injectors and fuel pumps only supporty HP, they do not create HP. See pic below of popular injectors for our vehicle. You won't need to step up in injector size unless you upgrade your cylinder heads to a better flowing piece like TFS, AFR, or Edelbrock or if you were to go with forced induction.

 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,131
10,748
213
polk county florida
Aug 14, 2017
#5
  • Aug 14, 2017
  • #5
Get the engine to run correctly before you pull it out, things can get really hard to fix if you don't. Run the codes, there is a thread in the 5.0 tech/how to section,
I'm also curious why the maf wires where spliced, and how it was done, butt connectors would be a no no.
 
Reactions: Metalgearmoogle and revhead347

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,303
1,649
214
Acworth, GA
Aug 14, 2017
#6
  • Aug 14, 2017
  • #6
karthief said:
Get the engine to run correctly before you pull it out, things can get really hard to fix if you don't. Run the codes, there is a thread in the 5.0 tech/how to section,
I'm also curious why the maf wires where spliced, and how it was done, butt connectors would be a no no.
Click to expand...

This. Much easier to get it run correctly first then try and work out the kinks on a new engine. Most sputters are ignition, not injectors. Check all the ignition stuff and the timing first.

I rarely recommend rebuilding engines in that performance range anymore. You can get a rebuilt short block at your favorite parts store for a fraction of what it cost to rebuild. Is it the best engine, no? Do you really need a torque plate honed short block for an iron head cruiser, no? Just something to think about.

Kurt
 
T

tubbaguts

Member
May 22, 2017
14
3
13
Aug 15, 2017
#7
  • Aug 15, 2017
  • #7
Thank you for all the feed back folks. Has given me some options I had not thought about.
 
You must log in or register to reply here.

Similar threads

O
Sooty/Oily Front Engine & Pulleys
  • ozenator
  • Jun 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
537
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 22, 2026
Blackhawkxx
S
5.0 Rebuild
  • smittys7up
  • Nov 29, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
14
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 16, 2026
keel
N
Looking for ECU/CHIP for 1992 5.0
  • Nathan26
  • Sep 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
9
Views
339
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 8, 2026
Qtrhrse23
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
730
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
617
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?