• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

everyone with trick flow stage 1 cam please!

  • Thread starter Thread starter mootang
  • Start date Start date Dec 18, 2004

mootang

New Member
Dec 5, 2004
907
0
0
texas
Dec 18, 2004
#1
  • Dec 18, 2004
  • #1
I have a trick flow stage 1 cam sitting in my room and its going in after christmas. I just want to hear from people running this cam. what do you like? dislike? about it. or
 

pleasehelp

New Member
Mar 11, 2003
686
0
0
Poplar Grove, Il
Dec 18, 2004
#2
  • Dec 18, 2004
  • #2
Registering. Will like to know as well. Will be installing it with the rest of the TFS engine kit.
 

Eric94GTvert

Founding Member
May 13, 2002
596
1
16
PA, Nazareth
Dec 18, 2004
#3
  • Dec 18, 2004
  • #3
I have the TFS stage 1 cam.

Things I like:
1. hasn't stalled or died on me with no tune
2. really gets the car going 3000+ rpms
3. runs better than I expected
4. car sounds freakin awesome
5. dirt cheap
6. hasn't let me down as a daily driver
7. will be good if I decide to go poweradder.

Things I don't like:
1. under 3000 rpms could have more grunt
2. begins to buck at 1500rpm (most cams)
3. knowing I left power on the table compared to a custom or bigger cam
4. new surge (800-1200rpms) until warmed up <40* outside.
 

mootang

New Member
Dec 5, 2004
907
0
0
texas
Dec 18, 2004
#4
  • Dec 18, 2004
  • #4
I know this isn't the only guy on here running a trick flow stage 1 cam.
 

1105

I AM the random post master...bow down
May 3, 2003
3,841
0
0
Daytona Bch, FL
Dec 18, 2004
#5
  • Dec 18, 2004
  • #5
I'm running the same cam, and I agree with everything Eric said. I have a sould clip if you want to hear it... Shoot my an IM and I'll send it to you.
 

blksn955.o

Founding Member
Mar 15, 2002
3,263
0
66
st.louis mo 314
Dec 18, 2004
#6
  • Dec 18, 2004
  • #6
I ran this in my old setup and it is also in the new one. With no tune it ran fine for the most part. At cold startup or when it was cold out it would stall if left to idle on its own. Every once and a blue moon it would die at a stoplight if I slowed down too fast seemed the idle just droped to fast and it could not recover. Driving there was alittle bit of bucking at low speeds/light throt. like you were taping the gas even though you were not. The power was about stockish maybe alittle soft under 2,500rpms but after that it woke up fast and hard and pulled to the 5k mark with unported gt40 heads, and tmoss stock gt lower.

I ran 13.5 or was it 13.6 @ 102mph (the only fairly healthy pass I made with that setup), I also put down 230rwhp/281rwtrq. after I lost #4 cyl., had 33% press. drop in a leakdown/comp. check, so it made preaty good power.

I dont have any drive time in the car yet with the new motor so I cannot say what I have noticed about it. I also now have a tweecerR/T so I should be able to get great drivabilty out of it no matter what now.
 

final5-0

Mustang Master
Apr 6, 2003
6,817
12
79
DFW Texas
Dec 19, 2004
#7
  • Dec 19, 2004
  • #7
Chopped Liver said:
I have the TFS stage 1 cam.

Things I like:
1. hasn't stalled or died on me with no tune
2. really gets the car going 3000+ rpms
3. runs better than I expected
4. car sounds freakin awesome
5. dirt cheap
6. hasn't let me down as a daily driver
7. will be good if I decide to go poweradder.

Things I don't like:
Click to expand...

1. under 3000 rpms could have more grunt
Click to expand...

That is where a custom gives you the option to tell your cam guy you want him give you that low end torque.

2. begins to buck at 1500rpm (most cams)
Click to expand...

You can go way more radical with the cam than you think (we are talking street NOT race cams) and not have to deal with that kind of stuff if you are willing to custom tune the car.

3. knowing I left power on the table compared to a custom or bigger cam
Click to expand...

This is true when talking about the cam. Again with a way to custom tune you go for more power by going for a hotter cam. This way you give no consideration to pcm induced drivability problems when deciding on your cam specs.

4. new surge (800-1200rpms) until warmed up <40* outside.
Click to expand...

Custom tune can make if go away.

Having to deal with these things with cars in the past I do agree with you about these issues. I do feel I slayed most of those dragons with the exception of #3.

If I knew then what I know now about self tuning with my Tweecer I would have told Ed to go more radical with my cam. Like you I left some power on the table

Later
Grady
 

mootang

New Member
Dec 5, 2004
907
0
0
texas
Dec 20, 2004
#8
  • Dec 20, 2004
  • #8
I live in so cal so i wont have any problems with a surge below 40*
 
R

Rock777

Member
Aug 22, 2004
195
1
16
Troy, IL
Dec 21, 2004
#9
  • Dec 21, 2004
  • #9
I agree with just about everything said above. I really like this cam, if I had to pick an off-the-shelf cam again, I would still pick this one. It sounds very nice and lopey at about 750 rpms, but I have mine set about 1000 now in the winter time due to the surging when cold.
 

mootang

New Member
Dec 5, 2004
907
0
0
texas
Dec 21, 2004
#10
  • Dec 21, 2004
  • #10
rock777, what kind of fuel are you running with that timing?
 
R

Rock777

Member
Aug 22, 2004
195
1
16
Troy, IL
Dec 21, 2004
#11
  • Dec 21, 2004
  • #11
Well, right now I have the timing set at 16 and am running 87 octane with no pinging.
 

Jo_885o

New Member
Jul 17, 2003
422
0
0
Clint. Twp, Michigan
Dec 21, 2004
#12
  • Dec 21, 2004
  • #12
Rock777 have been to the track or had it tuned yet?
 
R

Rock777

Member
Aug 22, 2004
195
1
16
Troy, IL
Dec 21, 2004
#13
  • Dec 21, 2004
  • #13
No, I have not done either. I want to go to the track very,very badly but it closed about 2 weeks before I finished the rebuild, which is weird because I read about people on here still going, makes me jealous. Anyway, as far as tuning, I have looked into it but after everything I've bought lately, I don't have the funds for it right now, although it is in my future plans. I am pretty sure my car is running rich and I can't afford to do anything about it now because a tweecer, pms, or even chip is out of the picture for a little bit. Oh well, I am very happy the way it is running, just dying to run into an LS1 to see just HOW good.
 

mootang

New Member
Dec 5, 2004
907
0
0
texas
Dec 21, 2004
#14
  • Dec 21, 2004
  • #14
does anyone w/the stage1 cam have a dyno sheet or horsepower #'s they can post
 

Eric94GTvert

Founding Member
May 13, 2002
596
1
16
PA, Nazareth
Dec 21, 2004
#15
  • Dec 21, 2004
  • #15
Here's my dyno from a couple months ago.

 
Reactions: Hollywood_Vae
C

CArkid0101

New Member
Oct 7, 2004
76
0
0
Meno Falls, WI
Dec 21, 2004
#16
  • Dec 21, 2004
  • #16
Anyone have a link of where i can get one at a decent price, im gunna start looking into that h/c/i business, maybe next summer start putting her together after i get my second car, thx
 

mo_dingo

20+ Year Stangneter
Aug 26, 2003
3,031
2
58
Tucson, AZ
Dec 21, 2004
#17
  • Dec 21, 2004
  • #17
Chopped Liver said:
Here's my dyno from a couple months ago.

Click to expand...

Nice graph....I like it!!!
Scott
 

mootang

New Member
Dec 5, 2004
907
0
0
texas
Dec 22, 2004
#18
  • Dec 22, 2004
  • #18
nice graph!!

What kind of dyno was that on??

I see what people were talking about when they say no power till around 3g.
 
You must log in or register to reply here.

Similar threads

Engine Hiccup at full throttle
  • keel
  • Jun 2, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
31
Views
1K
Fox 5.0 Mustang Tech Jul 30, 2026
keel
F
Ford 460 swap
  • Ford460
  • Sep 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
506
1996 - 2004 SN95 Mustang -General/Talk- Sep 14, 2026
Ford460
F
SOLD Trick Flow Box R Series Upper Intake w/90 mm Inlet
  • Habu135
  • Apr 30, 2026
  • Engine and Power Adder
Replies
2
Views
403
Engine and Power Adder Aug 19, 2026
Habu135
5
Hello Everyone !
  • 5150K
  • Jul 3, 2026
  • The Welcome Wagon
Replies
0
Views
189
The Welcome Wagon Jul 3, 2026
5150K
5
Surging/stalling! problem or tune?
  • djj62478
  • Oct 4, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
411
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 14, 2026
KRUISR
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?