• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Exhaust Install Question

  • Thread starter Thread starter savegoodautonfg
  • Start date Start date Jul 8, 2006
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Jul 8, 2006
#1
  • Jul 8, 2006
  • #1
Whats up everyone..

Right now i got the 2 chamber flows with the o/r h-pipe and tailpipes. soon im going to cut off my tailpipes and mufflers and put on dynomax race bullets with dumps. i don't have the money right now to pay a mechanic to install and weld them. whats the best way to install them without welding? i read somewhere about band clamps. i want to ensure that there will be no leaks.

Thanks in advance for the replies.
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 8, 2006
#2
  • Jul 8, 2006
  • #2
clamps,bands whatever you use with dynomax race bullets with dumps if they leak at the clamp or band you will not know it because it will be loud. but heres a link to the clamps below. i would price the cost to get them welded in after you cut exhaust it should less than twice the price you would pay for the clamps..

http://store.summitracing.com/egnse...094-2250&searchinresults=false&N=115&y=7&x=31
 
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Jul 8, 2006
#3
  • Jul 8, 2006
  • #3
Ok now one more question i was just trying to figure this all out. i was going to get 2 1/2 ID turndowns. the mufflers says 2 1/2 ID/OD and im almost positive my exhaust tubing/pipes is 2 1/2. the clamps were also 2-1/2'' Preformed Exhaust Band Clamp .

Will all of this fit correctly if not can you help me as to what will?
 

GearHd6

Member
Jul 19, 2005
459
0
18
Ashford, CT
Jul 8, 2006
#4
  • Jul 8, 2006
  • #4
How can the muffler be 2 1/2 Inside Diameter AND Outside Diameter? Seems like its either ID or OD not both. Unless they're universal somehow.
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 8, 2006
#5
  • Jul 8, 2006
  • #5
GearHd6 said:
How can the muffler be 2 1/2 Inside Diameter AND Outside Diameter? Seems like its either ID or OD not both. Unless they're universal somehow.
Click to expand...
ID= inlet diameter....OD= outlet diameter
 

GearHd6

Member
Jul 19, 2005
459
0
18
Ashford, CT
Jul 8, 2006
#6
  • Jul 8, 2006
  • #6
Well thats friggin confusing as all hell. I guess im still stuck in my old machinist days.
 
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Jul 8, 2006
#7
  • Jul 8, 2006
  • #7
Ok now one more question i was just trying to figure this all out. i was going to get 2 1/2 ID turndowns. the mufflers says 2 1/2 ID/OD and im almost positive my exhaust tubing/pipes is 2 1/2. the clamps were also 2-1/2'' Preformed Exhaust Band Clamp .

Will all of this fit correctly if not can you help me as to what will?
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 8, 2006
#8
  • Jul 8, 2006
  • #8
you need 2.5 inch outer diameter turndowns which will fit into your mufflers and if you have a 2.5 inch exhaust the bullets will slip right in to your existing exhaust pipe...if not and you have a 2.25 in exhaust you will need to buy a reducer..also if your using clamps you will need 4...
 
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Jul 8, 2006
#9
  • Jul 8, 2006
  • #9
bill302 said:
you need 2.5 inch outer diameter turndowns which will fit into your mufflers and if you have a 2.5 inch exhaust the bullets will slip right on...if not and you have a 2.25 in exhaust you will need to buy a reducer..also if your using clamps you will need 4...
Click to expand...

thanks alot bill, 2.5" clamps also.

can i have some links to where i can get the 2.5 inch outer diameter turndowns?
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 8, 2006
#10
  • Jul 8, 2006
  • #10
http://www.jegs.com/webapp/wcs/stor...eId=10001&categoryId=23043&searchItemId=91311
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 8, 2006
#11
  • Jul 8, 2006
  • #11
i confirmed all the info. i gave you with jegs and its correct to verify you can call 1-800-345-4545...
 
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Jul 8, 2006
#12
  • Jul 8, 2006
  • #12
That is ID.... you said i need outside diameter
 

larrendeuce

Member
Sep 13, 2003
649
1
19
Southern NJ
Jul 8, 2006
#13
  • Jul 8, 2006
  • #13
I use the supertrapp clamps in my exhaust. They are weak and more trouble then they are worth. During tightening they collapse and its hell to get them back off. I also went with these clamps to finish with butt joints.
http://store.summitracing.com/partdetail.asp?autofilter=1&part=WLK%2D33240&N=115&autoview=sku

They come with Grade 8 bolts and are much easier to use then the supertrapp ones. Just scrape off the tar patch that comes on them(you'll know what I mean when you see it) it gets everywhere and I ruined a clamp in the process. I like these clamps better then the ball and socket flanges. No leaks.
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 8, 2006
#14
  • Jul 8, 2006
  • #14
i am getting conflicting information from jegs let me do some more research....
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 8, 2006
#15
  • Jul 8, 2006
  • #15
you need the mufflers they will slide right onto your exhaust (2 1/2 if that is what you have) where you cut it and clamp it then you need a part number 41094 from jegs this part is not listed on the site or magazine (call jegs) its the turndown made by dynomax to fit into their mufflers $16.99 each and use 1 more clamp (heres a link to the clamps i would use) http://www.jegs.com/webapp/wcs/stor...Id=10001&categoryId=28109&searchItemId=318567 to hold turndown in place.. this is the dynomax tech line and where i got the info... (734) 384-7806..i also called a local muffler shop who does all my work they said they charge $45 to weld muffler in and to make some turn downs and weld them in after you cut exhaust.so you might want to call a local muffler shop you may be able to get it welded in and some turndowns made for about the same price as the turndowns and clamps from jegs....
 

mob

the guy who hits on his mom
20+ Year Stangneter
Oct 3, 2003
2,566
136
104
Dallas, TX
Jul 9, 2006
#16
  • Jul 9, 2006
  • #16
honestly just call around ask someone how much it would cost to weld on two mufflers and turn downs, cut the pipes before the mofflers and drive it to some hilly billy muffler guy. Cost me 60 bucks, for the guy to cut and weld, im sure itll even out to that if you cut it yourself and tell him to put turn downs on it, I dont have turn downs on mine.
 
S

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Jul 23, 2006
#17
  • Jul 23, 2006
  • #17
I had one more question about the turndown pipes.

will it be too close to the rear end axle's and the whole rear end in general with the turndowns on?
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 23, 2006
#18
  • Jul 23, 2006
  • #18
don't worry about it that is why most people use turndowns to keep exhaust from exiting straight onto axle causing it to heat up.
 
You must log in or register to reply here.

Similar threads

G
1982 Mustang GL 5.0 single to dual exhaust conversion
  • Guyton
  • Jun 27, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
15
Views
970
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 1, 2025
limp
M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
865
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
Alternator not charging
  • SchwarzStock
  • Jul 6, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
3
Views
270
1965 - 1973 Classic Mustangs -General/Talk- Oct 17, 2026
SchwarzStock
P
Tailpipes for '88 GT
  • pindude80
  • Apr 30, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
31
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 13, 2025
pindude80
P
S
Fox Another try for the European guy to get his first Fox
  • Schargedfox
  • Aug 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
399
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 4, 2026
DadLife0724
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?