Exhaust Install Question

savegoodautonfg

New Member
May 11, 2005
1,085
0
0
Whats up everyone..

Right now i got the 2 chamber flows with the o/r h-pipe and tailpipes. soon im going to cut off my tailpipes and mufflers and put on dynomax race bullets with dumps. i don't have the money right now to pay a mechanic to install and weld them. whats the best way to install them without welding? i read somewhere about band clamps. i want to ensure that there will be no leaks.

Thanks in advance for the replies.
 
Ok now one more question i was just trying to figure this all out. i was going to get 2 1/2 ID turndowns. the mufflers says 2 1/2 ID/OD and im almost positive my exhaust tubing/pipes is 2 1/2. the clamps were also 2-1/2'' Preformed Exhaust Band Clamp .

Will all of this fit correctly if not can you help me as to what will?
 
Ok now one more question i was just trying to figure this all out. i was going to get 2 1/2 ID turndowns. the mufflers says 2 1/2 ID/OD and im almost positive my exhaust tubing/pipes is 2 1/2. the clamps were also 2-1/2'' Preformed Exhaust Band Clamp .

Will all of this fit correctly if not can you help me as to what will?
 
you need 2.5 inch outer diameter turndowns which will fit into your mufflers and if you have a 2.5 inch exhaust the bullets will slip right in to your existing exhaust pipe...if not and you have a 2.25 in exhaust you will need to buy a reducer..also if your using clamps you will need 4...
 
bill302 said:
you need 2.5 inch outer diameter turndowns which will fit into your mufflers and if you have a 2.5 inch exhaust the bullets will slip right on...if not and you have a 2.25 in exhaust you will need to buy a reducer..also if your using clamps you will need 4...

thanks alot bill, 2.5" clamps also.

can i have some links to where i can get the 2.5 inch outer diameter turndowns?
 
I use the supertrapp clamps in my exhaust. They are weak and more trouble then they are worth. During tightening they collapse and its hell to get them back off. I also went with these clamps to finish with butt joints.
http://store.summitracing.com/partdetail.asp?autofilter=1&part=WLK%2D33240&N=115&autoview=sku

They come with Grade 8 bolts and are much easier to use then the supertrapp ones. Just scrape off the tar patch that comes on them(you'll know what I mean when you see it) it gets everywhere and I ruined a clamp in the process. I like these clamps better then the ball and socket flanges. No leaks. :nice:
 
you need the mufflers they will slide right onto your exhaust (2 1/2 if that is what you have) where you cut it and clamp it then you need a part number 41094 from jegs this part is not listed on the site or magazine (call jegs) its the turndown made by dynomax to fit into their mufflers $16.99 each and use 1 more clamp (heres a link to the clamps i would use) http://www.jegs.com/webapp/wcs/stor...Id=10001&categoryId=28109&searchItemId=318567 to hold turndown in place.. this is the dynomax tech line and where i got the info... (734) 384-7806..i also called a local muffler shop who does all my work they said they charge $45 to weld muffler in and to make some turn downs and weld them in after you cut exhaust.so you might want to call a local muffler shop you may be able to get it welded in and some turndowns made for about the same price as the turndowns and clamps from jegs....
 
honestly just call around ask someone how much it would cost to weld on two mufflers and turn downs, cut the pipes before the mofflers and drive it to some hilly billy muffler guy. Cost me 60 bucks, for the guy to cut and weld, im sure itll even out to that if you cut it yourself and tell him to put turn downs on it, I dont have turn downs on mine.