• Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech

Finally Off to Paint

  • Thread starter Thread starter geordie
  • Start date Start date Feb 12, 2007
G

geordie

Founding Member
May 10, 2002
576
2
19
Feb 12, 2007
#1
  • Feb 12, 2007
  • #1
Two years into the project and the car is finally off to paint.
The engine, 302 small block, 11.5:1 compression, overbored .030", has been removed, repainted, fitted with new Edelbrock water pump, Edelbrock RPM intake, edelbrock fuel pump and Canton oil pan. It has been dressed up with Ford Racing valve covers and chrome dipstick tube.
The transmission, driveshaft, front and rear windows, bumpers, badges, chrome trim, entire interior, headliner, gas tank, front and rear valances, and hood were removed.
The front valance has been replaced with a Shelby style glass fiber item from Branda.
The hood has been replaced with a Shelby style glass fiber on steel frame from NPD and the rear valance has been replaced with a steel GT style item also from NPD.
The paintwork is to be Ford Sonic Blue with Ford Performance White Shelby stripes. The badges will not be replaced, neither will the antenna, the holes being welded shut.
So far the autobody shop have removed the doors, fenders and front sheet metal. The doors and hood have been aligned. Body work repairs will be carried out this week and hopefully the car will be painted next week.
Thanks for helping me get this far guys.
 

Attachments

  • Stangnet1.webp
    27.1 KB · Views: 213
  • Stangnet2.webp
    32.6 KB · Views: 229

krash kendall

Active Member
Nov 19, 2004
1,258
0
36
Aldergrove, B.C. Canada
Feb 12, 2007
#2
  • Feb 12, 2007
  • #2
Can't wait to see it!
 
M

mustangdave

My rearend needs a stud and two nuts.
Founding Member
Feb 26, 2002
2,976
1
56
North Carolina
Feb 12, 2007
#3
  • Feb 12, 2007
  • #3
Damn, that's some shiny paint to paint over.
 

geostang351

Member
Mar 30, 2005
946
0
17
Danb., CT
Feb 12, 2007
#4
  • Feb 12, 2007
  • #4
mustangdave said:
Damn, that's some shiny paint to paint over.
Click to expand...

My thoughts exactly!
 

1965stangcoupe

New Member
Sep 7, 2006
82
0
0
Mount Vernon Washington
Feb 13, 2007
#5
  • Feb 13, 2007
  • #5
How did the fiber glass parts fit? Do they have to be modified to fit right or are they quality enough that you dont have to? I was gonna go with a shelby valnce and hood but bagged the hood for mooney reasons and from reading that everyone has to do alot of work to fit them right. How was yours? I am really wondering about the front valance though.

Can't wait to see it done! Gonna look really nice in that sonic blue! congrats on making it this far!
 
G

geordie

Founding Member
May 10, 2002
576
2
19
Feb 13, 2007
#6
  • Feb 13, 2007
  • #6
I agree the paint is very shiny on the sides, but the AZ sun has baked the clear coat off all the upper surfaces, hood, roof and trunk. Also I can't abide the color.
Both the valance from Branda and the hood from NPD were good pieces. The valance took a bit of fitting and doesn't perfectly match the joint at the fenders, but this is a 40 year old car after all. I couldn't use the stock harware for the valance to gravel shield fit as there wasn't enough flat land under the screws so I went with socket head cap screws instead. Hood was a nice piece and fit really well. It has a steel frame.
 
G

geordie

Founding Member
May 10, 2002
576
2
19
Apr 13, 2007
#7
  • Apr 13, 2007
  • #7
Some early shots I received today of the new paint .
The main color is Ford Sonic Blue to which will be added Ford Performance White Shelby stripes. Gives the car a whole new attitude.
Can't wait to see it tomorrow morning.
 

Attachments

  • MVC%2D001S.webp
    20 KB · Views: 185
  • MVC%2D005S.webp
    19 KB · Views: 204
G

geordie

Founding Member
May 10, 2002
576
2
19
May 15, 2007
#8
  • May 15, 2007
  • #8
Nearly done...........
 

Attachments

  • MVC%2D007S.webp
    35.2 KB · Views: 174

krash kendall

Active Member
Nov 19, 2004
1,258
0
36
Aldergrove, B.C. Canada
May 15, 2007
#9
  • May 15, 2007
  • #9
Geordie,

It looks great! Now to help keep it that way, you better upgrade to a dual bowl master cylinder.

Is the paint shop going to install all your glass for you?
 
P

paintballtommy

Member
Jan 31, 2004
244
0
16
concord, ca
May 15, 2007
#10
  • May 15, 2007
  • #10
if you dont mind me asking what are they charging you for bodywork and paint. and what did they do as far as the bodywork goes.

Tom
 

jikelly

20+ Year Stangneter
Jul 9, 2003
872
53
99
Lubbock Tx
May 15, 2007
#11
  • May 15, 2007
  • #11
geordie said:
I agree the paint is very shiny on the sides, but the AZ sun has baked the clear coat off all the upper surfaces, hood, roof and trunk. Also I can't abide the color.
Both the valance from Branda and the hood from NPD were good pieces. The valance took a bit of fitting and doesn't perfectly match the joint at the fenders, but this is a 40 year old car after all. I couldn't use the stock harware for the valance to gravel shield fit as there wasn't enough flat land under the screws so I went with socket head cap screws instead. Hood was a nice piece and fit really well. It has a steel frame.
Click to expand...

Same thing happened to my wife's car. I think I'm gonna try and put a fresh clear coat on it this summer.

My stang's almost finished too. Just gotta redo the bumper, wash and reundercoat the unibody and then through the engine and tranny back together and slide um in. Then I'll be cruzin again after nearly 2 years.

Just wish I knew what to do about upgrading my stupid lap belts. Why didn't Ford solve that problem for me back in 73?
 
G

geordie

Founding Member
May 10, 2002
576
2
19
May 15, 2007
#12
  • May 15, 2007
  • #12
Krash,
The new Painless wiring harness and dual master cylinder installations are first on the list. I'm either going to have a crack (pun) at installing the glass myself or pay some installer to do it.
Tom,
Car was very straight to start with. The front valance was replaced by me with a Shelby style glass fiber item from Branda. The stock hood was replaced by me with a Shelby style glass fiber on steel frame from NPD and the rear valance was replaced with a steel GT style item also from NPD, also by me. I removed the engine, transmission, drive shaft, gas tank, interior, external chrome, bumpers, badges, mirrors and glass.
The autobody shop removed the doors, fenders and front sheet metal. They repaired a couple of rust holes with new metal. Stripped the paint to bare metal where necessary around the door jams and windows, realigned the doors and hood, primed where necessary, prepared the existing paint surface and painted it. I'm hoping the final bill comes in below $6500 excluding tax.
 

SadbutTrue

Founding Member
May 1, 2002
2,391
4
49
Thousand Oaks, California
May 15, 2007
#13
  • May 15, 2007
  • #13
That sonic blue is easily my favorite new ford color... 03 Cobra in sonic blue... mmmm
 
G

geordie

Founding Member
May 10, 2002
576
2
19
May 16, 2007
#14
  • May 16, 2007
  • #14
SadbutTrue said:
That sonic blue is easily my favorite new ford color... 03 Cobra in sonic blue... mmmm
Click to expand...

Personally I strictly a 65 - 73 and 2005 - present guy
 
You must log in or register to reply here.

Similar threads

S
Fox Another try for the European guy to get his first Fox
  • Schargedfox
  • Aug 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
351
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 4, 2026
DadLife0724
Old guy new to Forum.
  • 08shelby GT500
  • Jun 15, 2026
  • The Welcome Wagon
Replies
3
Views
223
The Welcome Wagon Jun 15, 2026
LILCBRA
R
What's it Worth? 1997 Cobra, a ton of mods and restoration
  • riored97snake
  • Jun 18, 2026
  • What is it Worth?!?!?
Replies
2
Views
418
What is it Worth?!?!? Jun 21, 2026
riored97snake
R
What's it Worth? 2000 GT
  • Mustang5L5
  • May 8, 2026
  • What is it Worth?!?!?
Replies
6
Views
454
What is it Worth?!?!? Jun 13, 2026
KRUISR
J
For Sale MASTER LISTING: Abandoned '66 Mustang Restomod Part-Out (Wilwood, Ididit, Quick Performance, Mishimoto)
  • JasonB66
  • Jul 23, 2026
  • Suspension
Replies
0
Views
282
Suspension Jul 23, 2026
JasonB66
J
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?