Finished My Cobra Project. Pics + Vids

acoddo · Aug 28, 2017

After much anticipation and aggravation, after deciding to help with the install of my Heads, Intake and Cam, I am finally finished. Had problems with the 24LB injectors and 24LB MAF, so I will have to install those later when I get a tune to go with it and maybe a blower. lol. Anyway here's the pics.

Guess you're only getting one picture since I'm getting an error with every other upload attempt. Oh well. Heres a couple videos.

View: https://www.youtube.com/watch?v=gyJqLP6I0j8

View: https://www.youtube.com/watch?v=HlulYSPXxQ8

95BlueStallion · Aug 28, 2017

Sounds good man. Are you running on the stock injectors and MAF right now?

89ripper · Aug 28, 2017

How do you like it? Im running the f cam as well in my setup.

acoddo · Aug 28, 2017

95BlueStallion said:
Sounds good man. Are you running on the stock injectors and MAF right now?

Running stock MAF and 19lb "multi spray" injectors. We couldn't get her to stop stalling with the 24lb injector/ MAF setup, but I blame the injectors that I got. Going to try a different brand later and try tuning

acoddo · Aug 28, 2017

89ripper said:
How do you like it? Im running the f cam as well in my setup.

So far, the idle is a little bit jumpy but she'll equalize over the next couple of days. It's 100% driveable, sounds awesome and feels great. big difference from stock.

Reddevil91 · Aug 28, 2017

Damn that sounds good, that cobra is clean where'd you find it? What heads are those, I know GT40 alum. But what version? I have about the same set up currently. Got f-303 with 1.7s with stock heads and intake. Just picked up a clean tubular GT40 upper and lower, 24lb inj. With mass air to go with it. Stuck on heads though can't decide.

acoddo · Aug 28, 2017

Reddevil91 said:
Damn that sounds good, that cobra is clean where'd you find it? What heads are those, I know GT40 alum. But what version? I have about the same set up currently. Got f-303 with 1.7s with stock heads and intake. Just picked up a clean tubular GT40 upper and lower, 24lb inj. With mass air to go with it. Stuck on heads though can't decide.

A lot of it boils down to what your goals are. For me, I loved the look of the cobra intake. Found it at a junkyard from Connecticut and had it shipped to me. I went with the aluminum gt40 heads off ebay and f cam because those three are all decent power gain and not super tricky to put together. All Ford on Ford parts, no messing with some of the other setups. Some of the more expensive stuff like trickflow might give you better top end power and there's the cheaper shorter intakes that are great for torque. The intake was in good condition when I got it, but I had it sandblasted and powdercoated.

imp · Aug 28, 2017

@acoddo
My '93 Cobra (factory) ran exceedingly well. The kicker was, if I bought it, and fixed the RF fender damage, it would become my wife's daily driver to work. How could I refuse?

Have almost no pics of it. We had little dough, needed tires, had the early Fox rims around, so.......she didn't mind. Gave the car to my nephew who is in the Marine Corps. He has it mothballed in Kansas.

Wondering if you went with roller-rocker arms, as Cobra came factory with them. imp

Reddevil91 · Aug 29, 2017

acoddo said:
A lot of it boils down to what your goals are. For me, I loved the look of the cobra intake. Found it at a junkyard from Connecticut and had it shipped to me. I went with the aluminum gt40 heads off ebay and f cam because those three are all decent power gain and not super tricky to put together. All Ford on Ford parts, no messing with some of the other setups. Some of the more expensive stuff like trickflow might give you better top end power and there's the cheaper shorter intakes that are great for torque. The intake was in good condition when I got it, but I had it sandblasted and powdercoated.

Nice man yeah cobra and tubular GT40 have always looked great. I'm actually getting mine blasted &a powder coated now. For the heads are the GT40 X306 or 307s? I had an option for picking up some GT40 Y aluminum heads for 500, from the guy I bought my intake from, looked clean but hesitated and they sold. Debating between GT40 X, SVEs which everyone says to pass on or the TFs which I guess are their base idk like 1300 on lmr. I just know those three all work with the F-303 but I guess since they are Stud mount I'd have to buy new rockers which sucks. Can you change Stud mount to pedestal or is that not an option? I'm know mechanic/technician I just order parts then find a good speed shop or someone who knows mustangs.

Reddevil91 · Aug 29, 2017

imp said:
@acoddo
My '93 Cobra (factory) ran exceedingly well. The kicker was, if I bought it, and fixed the RF fender damage, it would become my wife's daily driver to work. How could I refuse?

Have almost no pics of it. We had little dough, needed tires, had the early Fox rims around, so.......she didn't mind. Gave the car to my nephew who is in the Marine Corps. He has it mothballed in Kansas.

Wondering if you went with roller-rocker arms, as Cobra came factory with them. imp

Awe man you put the bullet holes on the cobra

acoddo · Aug 29, 2017

Reddevil91 said:
Nice man yeah cobra and tubular GT40 have always looked great. I'm actually getting mine blasted &a powder coated now. For the heads are the GT40 X306 or 307s? I had an option for picking up some GT40 Y aluminum heads for 500, from the guy I bought my intake from, looked clean but hesitated and they sold. Debating between GT40 X, SVEs which everyone says to pass on or the TFs which I guess are their base idk like 1300 on lmr. I just know those three all work with the F-303 but I guess since they are Stud mount I'd have to buy new rockers which sucks. Can you change Stud mount to pedestal or is that not an option? I'm know mechanic/technician I just order parts then find a good speed shop or someone who knows mustangs.

Honestly this was my first time doing anything like this. I was more of the helper / watcher than the prime worker

Black1987 · Aug 29, 2017

acoddo said:
Honestly this was my first time doing anything like this. I was more of the helper / watcher than the prime worker

Glad to here the heads worked out for you. Now go run it and/or dyno it so we can see the power difference.

Did you have any previous passes on the old motor?

Finished My Cobra Project. Pics + Vids

acoddo

Active Member

95BlueStallion

My assy trans to myself

89ripper

acoddo

Active Member

acoddo

Active Member

Reddevil91

acoddo

Active Member

imp

Mustang Master

Reddevil91

Reddevil91

acoddo

Active Member

Black1987

my wife Bedazzled my input shaft

Similar threads

Finished My Cobra Project. Pics + Vids

Active Member

My assy trans to myself

Active Member

Active Member

Active Member

Mustang Master

Active Member

my wife Bedazzled my input shaft

Similar threads

Privacy & Transparency

Privacy & Transparency