First time 1/4 mile passes

[Trays GT]

This is the first time i ran this car down the 1/4 and i only had it for like 5 months, but i just recently picked up some welds skinnies and fattys with a 275/50/15 nitto drag radial, and this is my first stick shift, well anyways everything i have in my sig is what i ran with. All of this was done at Maryland International Raceway.

1st pass
R/T- .444
60'- 2.003 (3000 launch, 25 psi in tires)
1/8- 8.726
MPH- 80.21
1000- 11.368
1/4- 13.584
MPH- 104.19

(Surpise the crap outta me, i was so happy)

2nd pass
R/T- .292
60'- 2.233(3500 launch, 20 psi in tires)
330- 5.991
1/8- 8.946
MPH- 80.88
1000- 11.572
1/4- 13.784
MPH- 104.26

(Happy, but not like i was the first run)

3rd pass
R/T- .361
60'- 2.056(3000 launch, 20 psi in tires)
330- 5.789
1/8- 8.834
MPH- 80.63
1000- 11.465
1/4- 13.735(Darnit, i missed 4th)
MPH- 100.80(Darnit, i missed 4th, probably woulda been another 13.5 pass)

 

[Xanax]

I say great numbers Tray!
I have seen my friend run consistant 13.7's in his stock 02 GT Coupe with
just a K&N air filter at Capital Raceway.

 

[lopey4.6]

Great times.

Are you in the DC area Xanax? Have you ever heard of Espeut Performance in landover? He's my brother in-law and runs up there with the cars in my sig.

 

[smokin 04]

THOSE ARE SOME REALLY IMPRESSIVE NUMBERS!! HOPE MY CAR CAN TURN SIMILAR TIMES WHEN THE SNOW UP HERE FINALLY MELTS!!

 

[StngStr]

good job. you should be able to cut 1.7's with those drag radials. That will get your times down to low 13's. Get some gears so you're not in the bottom of 4th going through the traps.

 

[JonJon]

good job. you should be able to cut 1.7's with those drag radials. That will get your times down to low 13's. Get some gears so you're not in the bottom of 4th going through the traps.

 

[Too Slow]

lower the psi in those dr's down to like 15 next time and you should hook alot better.

 

[decoy562]

Nice numbers!

 

[Trays GT]

do yall really think those are good times , should i get in the 12's with electronic exhaust cutouts, bbk long tubes, off road x pipe, lighting mass air, accufab 75mm throttle body and upper plenum?? and also with 4.10's?? with the guys with 5 speeds, what are yalls rpms at 60 with 4.10's??

 

[Jackie Chan]

those are some pretty good times considering your mods, were you bogging or spinning? drop the tire pressure in the nittos to about 14psi and heat them up really good. I watched a guy cut 1.8s on stock gears launching off of the limiter on mccreary's, those nittos should do the same. all he had was a midpipe and mufflers though...13.4s. Your weather must be awesome up there for racing right now.

 

[xtrm281gt]

most of mr friends with drag radials drop them down to about 18 psi when they are racing... you might want to try that... they are running 13.0's with your mods, 4.10's, and dr's

 

[Daves4.6GT]

do yall really think those are good times , should i get in the 12's with electronic exhaust cutouts, bbk long tubes, off road x pipe, lighting mass air, accufab 75mm throttle body and upper plenum?? and also with 4.10's?? with the guys with 5 speeds, what are yalls rpms at 60 with 4.10's??

You could easily be in the 12s with good traction......but the cut outs will slow you down alot.......with out back pressure, fuel injected stangs have zero torque, try it, its worthless........

Dave

 

[Trays GT]

i can't wait till next time i go to the track, i going to try 3500 launch and see what i do