• Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech

FlowTech Glasspacks, yes or no?

  • Thread starter Thread starter 302RWP
  • Start date Start date Jun 29, 2004
3

302RWP

New Member
Feb 8, 2004
100
0
0
Northern California
Jun 29, 2004
#1
  • Jun 29, 2004
  • #1
hey guys i need to know if anybody uses glasspacks on their exhaust setup, if you do can you post some info about them. how do they sound? is the installation easy? FlowTech Im thinking about getting these because theyre so goddam cheap! any input is appreciated. EDIT: completely stock exhaust, dont know if it makes a difference but just to let you know ,
 
1

1969mach1351

Member
Apr 18, 2003
285
0
16
Sacramento, CA
Jun 29, 2004
#2
  • Jun 29, 2004
  • #2
When I bought my car it had something like glass packs but they were about 3 feet long. They just sounded like stock mufflers, not loud at all and not very good either.
 

MrBobMarley

Founding Member
Oct 7, 2002
460
0
16
Ft Myers, FL
Jun 29, 2004
#3
  • Jun 29, 2004
  • #3
Hey man , I have a bone stock exhaust except for some cheapo glasspacks the muffler guy had laying around, like 40 bucks for both or something. Here's a vid of a my stang, you be the judge. I'm not going WOT though, just giving it some gas.

I like the loud factor; I like scaring little kids and old people in buicks lol j/k. However, as far as sound goes packs have a clappy kind of sound and I think good ol flowmasters or dynomax's might give it a deeper, throatier rumble.

I like mine, but I'll probably swap out to mufflers later and who knows, I may not like them either and go back with packs. Good luck.

Right click, save as
 

MustangMatt1966

New Member
Mar 11, 2004
1,004
1
0
Orlando Fl.
Jun 29, 2004
#4
  • Jun 29, 2004
  • #4
i have the flowtech purple hornies with the turndown tip. They bolt strait onto the flowteck long tube headers i have, they were cheap and the sounds freaking awesome. My car sounds like a top fuel dragster, well kinda i would say go with them, i havent had any problems other than having to go slow over speed bumps, cuz they hang kinda low.
 

EL1NOR

Member
Apr 14, 2003
227
0
16
Hampstead, NH
Jun 29, 2004
#5
  • Jun 29, 2004
  • #5
I have 1966 Shelby GT-350 side exit exhaust on my 1967 Fastback with a 289... Sounds f***ing crazy on WOT, but cruisin' or at idle it just purs nice and low, not obscene or anything. I've heard glasspacks before and been like "jesus.. turn it down a bit, it sounds like a$$" but these are a lot larger sized and give it just the tone I wanted, I was damn lucky.


The pipes stuck out a bit further than I wanted but I had them heated and pulled forward just to the right spot. Bingo bango I'm done with my exhaust and I love it, along with everyone else at the shows and in my neighborhood.

-Tim
 
3

302RWP

New Member
Feb 8, 2004
100
0
0
Northern California
Jun 29, 2004
#6
  • Jun 29, 2004
  • #6
thanks guys, im probably gonna buy them for now until i figure out what to do for the exhaust. i wanna put flows w/ h-pipe but those are overplayed, but they just sound so nice. nice lookin stang mrbobmarley, sounds nice too. helped alot i like that setup you're running mustangmatt
 

MustangMatt1966

New Member
Mar 11, 2004
1,004
1
0
Orlando Fl.
Jun 29, 2004
#7
  • Jun 29, 2004
  • #7
thanks
 

MrBobMarley

Founding Member
Oct 7, 2002
460
0
16
Ft Myers, FL
Jun 29, 2004
#8
  • Jun 29, 2004
  • #8
Thanks also. The right glasspacks and side exit might be damn nice man. I know for a while I had hacked the tailpipes off my car for a little while, so I had dumps, but they didn't turn down. It was a bit louder than after I had the tailpipes put on, but I can feel more torque now. But then again, my engine is on its deathbed. Good luck, hope you're happy with your choice.
 
You must log in or register to reply here.

Similar threads

P
rear Impact absorbers.
  • Praetorious
  • May 4, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
162
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 5, 2026
Praetorious
P
J
Exhaust manifold to Y-pipe nut & stud dimensions?
  • joeybuddy96
  • Jul 7, 2026
  • SN95 V6 Mustang Tech
Replies
2
Views
88
SN95 V6 Mustang Tech Jul 9, 2026
joeybuddy96
J
P
market for 2.3L? i wanna sell
  • Patk
  • Dec 6, 2025
  • 2.3L (N/A & Turbo) Tech
Replies
5
Views
274
2.3L (N/A & Turbo) Tech Dec 7, 2025
rednotch
J
Transmission
  • Jraesims
  • Mar 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
181
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 8, 2026
JD1964
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
864
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • Classic Mustang Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?