• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

fuel problems

  • Thread starter Thread starter 89GtConvert5spd
  • Start date Start date Sep 28, 2005

89GtConvert5spd

New Member
Sep 5, 2005
58
0
0
Sep 28, 2005
#1
  • Sep 28, 2005
  • #1
alright so im still stumped on my problem about the running on 2 cylinders, (yes believe it or not i have a v8 idleing on 2 cylinders) but there was a tube going from the oil spout to the throttle body, so i pulled it off of the spout and poured gas directly into the throttle body and all the cylinders started fireing again...for a very short period..but the 2 more cylinders started running on their own..so i took it down the road and they all of a sudden quit, so im back down to 2. the 1 and 5 cylinder...so what im asking is could it possibly be the fuel pump?? or is it more likley injector wiring? or what...


thanks :damnit:
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Sep 28, 2005
#2
  • Sep 28, 2005
  • #2
Check your fuel presure there is a fitting behind the alternator for a fuel pressure gauge. You should see 38-40 PSI, engine idling with the vacuum line on the fuel pressure regulator disconnected. Correct any fuel pressure problems before proceeding any further.

Fuel pressure OK, the injectors are not firing, OR one or more injectors stuck open

Do a cylinder balance test: Warm the car's engine up to normal operating temperature. With the Engine Off, Key OFF, use a jumper wire or paper clip to put the computer into test mode. Start the engine and let it go through the normal diagnostic tests, then quickly press the throttle to the floor. The engine RPM should exceed 2500 RPM's for a brief second. The engine will shut off power to each injector, one at a time. When it has sequenced through all 8 injectors, it will flash 99 or the number of the failing cylinder such as 22 for cylinder #2. Quickly pressing the throttle again up to 2500 RPM’s will cause the test to re-run with smaller qualifying figures. Do it a third time, and if the same cylinder shows up, the cylinder is weak and isn’t putting out power like it should. See the Chilton’s Shop manual for the complete test procedure

The red wire on each injector is powered up whenever the ignition switch is in the Run position. The computer provides a ground to complete the circuit and fire the injector. The injector must have a ground to squirt fuel on command. A short to ground in the injector return wiring can cause one or more injectors to be continually open or triggered
A.) A Noid light available from Autozone, is one way to test the injector wiring. If the light stays on constantly, either the wiring has a short to ground or the computer has failed

B.) I like to use an old injector with compressed air applied to the injector where the fuel rail would normally connect. I hook the whole thing up, apply compressed air to the injector and stick it in a paper cup of soapy water. When the engine cranks with the ignition switch on, if the injector fires, it makes bubbles An injector stuck open will release a continual stream of bubbles. Cheap if you have the stuff laying around, and works good too. The same trick works great to find leaking injectors too.​
The wiring for the injectors may have some bare spots in it causing the injector to computer control wire to ground out. This would cause the injector to remain on anytime the key was in the Run position. Remove the injector wiring connectors from the injector. Note that each injector has one red wire for power and a non red wire (wire some color other than red) for computer controlled ground. With the key off, disconnect the computer connector from the computer. Use an Ohmmeter between the non red wire and ground. You should see more than 100000 (100K) ohms resistance.

See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host) for help




Using the above diagram, check the resistance between the injector and the computer. Clean and check the 10 pin connectors since they are a potential trouble source. Any resistance greater than 1 ohm between the injector to computer wire and the matching pin on the computer connector is a problem.



See http://fordfuelinjection.com/?p=6 for more help

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. You’ll need it to do the cylinder balance test

See http://www.troublecodes.net/Ford/
OR
See http://www.dalidesign.com/hbook/eectest.html for more descriptive help
OR
See http://www.mustangworks.com/articles/electronics/eec-iv_codes.html
 

Attachments

  • 88-91eecPinout.gif
    167.1 KB · Views: 95

89GtConvert5spd

New Member
Sep 5, 2005
58
0
0
Sep 28, 2005
#3
  • Sep 28, 2005
  • #3
well all that info should keep me busy for a while...thanks
 

89GtConvert5spd

New Member
Sep 5, 2005
58
0
0
Sep 28, 2005
#4
  • Sep 28, 2005
  • #4
i dont relly understand the paper clip thing...i found the 2 plugs in the engine bay but what do i do with em?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Sep 29, 2005
#5
  • Sep 29, 2005
  • #5
89GtConvert5spd said:
i dont relly understand the paper clip thing...i found the 2 plugs in the engine bay but what do i do with em?
Click to expand...
Follow the instructions in the links to find out which connections to jumper with the paper clip. That will put the computer in self test mode.Then you can start the car and run the cylinder balance test.
 
You must log in or register to reply here.

Similar threads

L
Engine Why won't the motor start if I have spark and fuel
  • LeviAnderson
  • Nov 20, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
561
Fox 5.0 Mustang Tech Nov 20, 2025
AeroCoupe
J
Having fuel issues
  • Jbands2v
  • Nov 2, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
70
SN95 4.6L Mustang Tech Nov 2, 2026
LILCBRA
B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
F
Fox 1990 Mustang GT 5.0 A9L – Engine suddenly shuts off but immediately restarts when key turned
  • FishermansFriend
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
683
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
General karthief
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
589
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?