Fuel Sending Unit Relay Switch

BlackLX5.0

New Member
Nov 14, 2005
76
0
0
I finally got the stang running but it stopped pumping gas, so i took the fuel sending unit relay switch out and put a wire in it and it started pumping. What do you guys think a new fuel sending unit relay switch will cost?

Thanks
 
The fuel level sending unit pathways should have nothing to do with the fuel pump energizing....... Are you talking about the fuel pump relay?
 
The fuel sending unit is for the Gas gauge level.
The Fuel Pump relay is what turns on the pump.
The relays can work intermittantly and also can get stuck on or just stop working..If you have fuel to the injector supply rail then maybe you dont have spark?
 
Sounds like Injectors are not squirting. I am not sure what all the relay you bypassed controls. If its mass air I know the eec looks for the fuel pump to be running. I belive it monitors the relay you took out. Maybe thats why it wont run.
 
my fuel pump is on, i have all new relays. think it might be the computer? the computer isn't original. my motor used to be carbureated but the guy put efi on since gas went up (BIG MISTAKE) and used some junkyard upper/lower manifolds, harness and computer :( :( :(
 
yes i did. my injectors aren't getting 12V fully, and my wires are fine. I'm stuck. I'm about to just hang it up and start saving my money for a fuel press. regulator, edelbrock performer, and holley 4160 and an air cleaner...and scrap this bs efi.
 
You could run a temporary (for diagnostics) jumper wire to the injector harness to confirm that the lack of 12 volts is the issue. If so, find the bad patch of wire (make sure nothing in pinched between hard parts, etc) or just run a new length of wire.

Good luck.
 
A key-on 12 volt source (the EEC relay output would be nice, since that is its original source). Any number of circuits would really work though (for 5 seconds worth of diagnostics only).
 
ZephyrMotorspor said:
jumper it from where?
If you need 12 volts, the battery is the obvious source.

If you are electrically challenged, speak up. I have some resources to help in that department.

The diagrams on my reply to your post are sufficient to get you where you need to go if you have a rudimentary knowledge of electricity.
 
Thanks for the help everyone, its greatly appreciated, But I got another question lol. I put my starter on today, but its not getting fire to make the starter turn over, but if I take a wire from the starter to the starter relay and cross them, it will start like that. What do you guys think might be wrong?

Thanks :SNSign:
 
That's a very vague description. What color are the wires? Are they the big thick wires or smaller ones?

Here's a checklist:

Since some of the tests will bypass the safety interlocks, make sure that the car is in neutral and the parking brake is set. Becoming a pancake isn’t part of the repair process…

Check battery, terminal connections, ground, starter relay switch (also known as solenoid) and starter in that order.

A voltmeter is handy if you are familiar with how to use it to find bad connections. Measure the voltage drop across a connection: more than .5 volts across a connection indicates a problem.
See http://www.fluke.com/application_notes/automotive/circuit.asp?AGID=1&SID=103 for help
fig-7.gif


1.) Will the car start if it is jumped? Then clean battery terminals and check battery.

2.) Check the battery to engine block ground, and the ground behind the engine to the firewall.

3.) Jump the big terminals on the starter relay next to the battery with a screwdriver - watch out for the sparks! If the engine cranks, the starter and power wiring is good. The starter relay is also known as a starter solenoid.

4.) Then pull the small push on connector (red wire) off the starter relay (Looks like it is stuck on a screw). Then jump between the screw and the terminal that is connected to the battery. If it starts, the relay is good and your problem is in the rest of the circuit.

5.) Remember to check the ignition switch, neutral safety switch on auto trans and the clutch safety switch on manual trans cars. If they are good, then you have wiring problems. See http://www.autozone.com/images/cds/gif/large/0900823d80195963.gif for 88-90 year cars .OR see http://www.autozone.com/images/cds/gif/large/0900823d80195964.gif for 91-93 year cars. See http://www.autozone.com/servlet/UiB..._us/0900823d/80/1d/db/3c/0900823d801ddb3c.jsp for 94-95 model cars.

6.) The starter may be hung, loosen up the bolts that hold it on, and give it a good whack with a big hammer. Tighten up the bolts and try again.

7.) If that doesn't work, use a jumper cable from the positive lead on the battery direct to the starter post where the big wire from the relay connects. If it cranks then, it is the power wire from the relay gone bad. This will be hard to do, since there isn't much room to do it.

8.) Pull the starter and take it to Autozone or Pep Boys and have them test it. Starter fails test, then replace it. If you got this far, the starter is probably bad.
 
Thanks for the help, I appreciate it. The starter is good, I just went to Autozone and had it tested yesterday. Im thinking its the nuetral safety switch, because the ways you said to start it up I have tried and it worked.

Thanks again :SNSign:
 
Sounds like #4 and 5 on Jrichker's list are where you are at.
I will echo a little of what is in Jrichker's post.

If you put a test light on the little slide-on (S terminal) on the solenoid and DONT have 12 volts to that little wire while cranking, the signal is not making it to the solenoid in the first place.

If so, the neutral safety switch is where I would look too. If you dont have 12 volts [during cranking] going into the neutral switch (BE VERY CAREFUL DURING ALL THIS TESTING SINCE THE CAR MIGHT DECIDE TO FINALLY START), then I would look further upstream (toward the ignition switch itself, and the wiring in between).

JRichker will have more detailed info for you.

Good luck.