• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

G-Force Tranny rebuild vs. TKO

  • Thread starter Thread starter zenboy99
  • Start date Start date Aug 2, 2004

zenboy99

Founding Member
May 12, 2002
2,212
0
47
Madison, WI
Aug 2, 2004
#1
  • Aug 2, 2004
  • #1
How many people on here have done this? How easy is the rebuild? Since most people on here agree that TKO swaps are upwards of $2000, this seems like a logical thing to do. I've seen the rebuild kits run for $900, and I can still use the stock bellhousing, etc. I'm sure the TKO is a better setup and could handle more power, but I'm only making 338rwtq.

Discuss
 

Killercanary

The car that set the bar.
Founding Member
Nov 29, 1999
5,676
1
76
Altoona, PA
Aug 2, 2004
#2
  • Aug 2, 2004
  • #2
I'm into my TKO swap for right at $2000, but I got a good deal on my TKO. Double check the TRUE cost of putting in the G force rebuild. I truely don't know it, but I was under the impression that it was higher than that. Also, even with stronger internals, you still have the same case that is prone to either break or "move." This moving motion is what causes the two shafts to seperate (especially in 3rd) and makes the gears only mesh with the tips of the gears... this is normally what leads to the most common failure in a T5... 3rd gear.
 

Rootus

Officially Addicted
Feb 8, 2003
6,659
1
0
Portland, Oregon
Aug 2, 2004
#3
  • Aug 2, 2004
  • #3
I would figure closer to $1500 for the G-Force if you do the labor yourself, $1800 or so if you get one that has been converted already. I have a very recent quote for a TKO for about $2000.

Paul -- I don't think it's the case that's the problem, it's that the stock T5 shafts are weak, and they bend. 3rd fails because it's in the middle of the shafts and gets the least contact patch under load. The G-Force internals are stronger so they do not bend.

Dave
 

zenboy99

Founding Member
May 12, 2002
2,212
0
47
Madison, WI
Aug 2, 2004
#4
  • Aug 2, 2004
  • #4
Here's a link I found for a kit, it doesn't include the syncro's though.

http://www.4speeds.com/t5/gforce.html

What else should I buy since I'd have the tranny torn apart?

Would this rebuild kit help?
http://www.5speeds.com/kit.htm
 

Killercanary

The car that set the bar.
Founding Member
Nov 29, 1999
5,676
1
76
Altoona, PA
Aug 2, 2004
#5
  • Aug 2, 2004
  • #5
Thanks Dave. I have heard internet rumors of the cases still flexing though... but they may just be rumors.


The 3550 trans has the same main shaft as the T5.... that's somthing for those concidering it to think about. That is why I didn't get one of those... I bent three of them in my T5.
 

Grn92LX

Fidanza Man!
Founding Member
Jan 14, 2001
6,819
64
129
New York
Aug 2, 2004
#6
  • Aug 2, 2004
  • #6
I'm about to buy a low mileage TKO for my car with a pro 50 shifter. $1,100 shipped, can't beat that I, personally think you cant go wrong either way, but for me buying a new tranny was just too much money. I like the g force and its .59 5th and the fact that its lighter. If I was buying new it would be between a tko 500 or a G force with the extras. Tough choice IMO and you dont need a new bellhousing or a shifter. I'm probably gonna get a mcleod blow proof and index it. I plan on using it with the 347 stroker I have planned so the tranny is gonna sit in my garage until I start the motor project. Should make it easier to index it. Instead of buying the 31 spline yoke for $79, I think im gonna get a 31 spline fms alum driveshatft for $200.
 

mo_dingo

20+ Year Stangneter
Aug 26, 2003
3,031
2
58
Tucson, AZ
Aug 2, 2004
#7
  • Aug 2, 2004
  • #7
Just a thought.

If the case is prone to "flexing", could you weld braces that start at the output shaft and go all the way to the front of the case?

I would think 4 braces, each at the corners of the transmission (i.e. 45, 135, 225 & 315 degrees) would do the trick.

Any thoughts?
Scott
 

blackmagic94

Founding Member
Jan 5, 2002
1,215
0
0
Tucson, Arizona
Aug 2, 2004
#8
  • Aug 2, 2004
  • #8
GForce are crooks, they took my money for 5 months before I finally got a refund for them not making me the rebulid kit. They suck, their product suck, and customer service sucks even more.

TKO II FOR LIFE
 

Killercanary

The car that set the bar.
Founding Member
Nov 29, 1999
5,676
1
76
Altoona, PA
Aug 2, 2004
#9
  • Aug 2, 2004
  • #9
blackmagic94 said:
GForce are crooks, they took my money for 5 months before I finally got a refund for them not making me the rebulid kit. They suck, their product suck, and customer service sucks even more.

TKO II FOR LIFE
Click to expand...


I've heard this oh too many times before, but I didn't want to spread internet gossip with no proof.... there is nothing like hearing it from the horses mouth though!



I suggest everyone looking into either of these trannies makes a call to either Bob Hanlon or Walt at Pro Motion Performance Powertrain. Walt's number is 800-771-6843 or 954-771-5575 or powertrainwarehs@aol.com Bob can be contacted through his website http://www.hanlonmotorsports.com I have worked with them both and have nothing but praise for both of them. Both deal with TTC and Gforce.

These are the guys I'd contact to answer the question of which is right for you. Let us know what they say.
 
You must log in or register to reply here.

Similar threads

Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
797
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
SN Mustang Magnum T56 swap
  • revhead347
  • May 24, 2024
  • 1994 - 1995 Specific Tech
Replies
15
Views
6K
1994 - 1995 Specific Tech Jun 28, 2026
GearHeadGuy
Place to Avoid: Jamison Auto Group in Gulfport, MS
  • D Durden
  • Oct 20, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
46
Views
3K
1965 - 1973 Classic Mustangs -General/Talk- Thursday at 9:44 PM
Noobz347
Ultimate 5-lug swap thread - new/updated
  • Mustang5L5
  • Jul 21, 2022
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
33
Views
34K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 13, 2024
qikgts
J
Need Help: 95 Mustang GT Engine Rebuild
  • jurban421
  • Jul 25, 2021
  • Other Auto Tech
Replies
0
Views
2K
Other Auto Tech Jul 25, 2021
jurban421
J
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?