• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Getting 3.73's Installed...

  • Thread starter Thread starter stang8384
  • Start date Start date Jan 20, 2017
S

stang8384

Member
Jan 18, 2017
38
4
18
NY
Jan 20, 2017
#1
  • Jan 20, 2017
  • #1
89 gt here! Sometime by spring, I will be will getting 3.73's installed. Should anything else be replaced or serviced while the rear end is apart? Thanks
 

billison

I like tinted tail
15 Year Member
Feb 27, 2006
2,607
1,094
184
stl
Jan 20, 2017
#2
  • Jan 20, 2017
  • #2
Bearings
 
Reactions: Davedacarpainter

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,134
10,752
213
polk county florida
Jan 21, 2017
#3
  • Jan 21, 2017
  • #3
Wheel bearings and seals, check the brakes/wheel cylinders, synthetic gear lube and friction modifier.
If you can spring for it an aluminum drive shaft or at least new u joints and drive shaft balance.
Oh, and an extra set of rear tires, have fun
 

CarMichael Angelo

my rearend will smell so minty fresh,
15 Year Member
Nov 29, 1999
10,641
8,909
234
Birmingham, al
Jan 21, 2017
#4
  • Jan 21, 2017
  • #4
The T-loc shouldn't be ignored. A high mile differential will have dead clutches. Nothing will be more of a pi sser than re-assembling the rear end w/ new bearings, only to ignore the T-loc and have one tire blazing away during a burnout.
(That would be me, speaking from personal experience, as recently as this last build)
75.00 extra that should've been spent on the dead diff while it was out right in front of me. And now that's one more thing that'll have to get dealt with after the fact.

And laying on your back under the car wrestling the ring gear out While all of that sticky, gooey, stinky 90wt gear oil is running back down your forearms is such fun.
 
Reactions: 90sickfox, Davedacarpainter, A5literMan and 2 others
S

stang8384

Member
Jan 18, 2017
38
4
18
NY
Jan 21, 2017
#5
  • Jan 21, 2017
  • #5
madmike1157 said:
The T-loc shouldn't be ignored. A high mile differential will have dead clutches. Nothing will be more of a pi sser than re-assembling the rear end w/ new bearings, only to ignore the T-loc and have one tire blazing away during a burnout.
(That would be me, speaking from personal experience, as recently as this last build)
75.00 extra that should've been spent on the dead diff while it was out right in front of me. And now that's one more thing that'll have to get dealt with after the fact.

And laying on your back under the car wrestling the ring gear out While all of that sticky, gooey, stinky 90wt gear oil is running back down your forearms is such fun.
Click to expand...

Car has 60k on it. As of now, there will be no blazing burnouts lol. I baby her. And I will not be doing the work. All that being said.. Should i still have the t-loc serviced?
 
S

stang8384

Member
Jan 18, 2017
38
4
18
NY
Jan 21, 2017
#6
  • Jan 21, 2017
  • #6
karthief said:
Wheel bearings and seals, check the brakes/wheel cylinders, synthetic gear lube and friction modifier.
If you can spring for it an aluminum drive shaft or at least new u joints and drive shaft balance.
Oh, and an extra set of rear tires, have fun
Click to expand...

I was looking at the aluminum driveshaft. Do you think that it's worth it?
 

A5literMan

At least it is lumpy...
5 Year Member
Jul 30, 2011
4,674
2,343
194
Illinois
Jan 21, 2017
#7
  • Jan 21, 2017
  • #7
stang8384 said:
I was looking at the aluminum driveshaft. Do you think that it's worth it?
Click to expand...
If you just baby the car it's not. Especially with 60k on your original. I'd probably look at some u joints and call it good. The aluminum piece is stronger,lighter(less of a power reduction),etc but for a nice day driver-overkill. Imo
 
Reactions: mikestang63

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,134
10,752
213
polk county florida
Jan 21, 2017
#8
  • Jan 21, 2017
  • #8
Sorry should have asked for more info, just change the u joints, I would have the shaft balanced, 60k mile nice day driver why 373s? If it's an auto ok
If its a stick I'd do 355s
Whats your reason for the gear change?
Don't get me wrong, great mod but 373s raise your rpms on the highway, lower gas mileage. JMO
 

hoopty5.0

mechanicus terribilis
15 Year Member
Dec 14, 2010
7,848
6,992
214
SW Houston
Jan 21, 2017
#9
  • Jan 21, 2017
  • #9
Regardless of miles, the car is 30 years old. Why tear it all the way down and only replace half of the parts, especially when they're so cheap?
 
S

stang8384

Member
Jan 18, 2017
38
4
18
NY
Jan 21, 2017
#10
  • Jan 21, 2017
  • #10
karthief said:
Sorry should have asked for more info, just change the u joints, I would have the shaft balanced, 60k mile nice day driver why 373s? If it's an auto ok
If its a stick I'd do 355s
Whats your reason for the gear change?
Don't get me wrong, great mod but 373s raise your rpms on the highway, lower gas mileage. JMO
Click to expand...

All stock, 5 speed. But I'd like to do some cost effective upgrades to help with performance. 2 of the top 3 I always read are gears and subframe connectors. Had the connectors done already.

Just trying get an idea for budget purposes. Unfortunately I'm not very mechanically inclined so I'll paying for labor for everything. I already have a leaking oil pan gasket and rear main seal to get fixed. Which I assume will be costly.
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,134
10,752
213
polk county florida
Jan 21, 2017
#11
  • Jan 21, 2017
  • #11
Buy a repair book, there are a lot of things even marginal mechanics can do to save money.
Right about the sub frame and the gears, although I would suggest going with 355s but it's your call.
Don't forget the brakes, they are good enough for driving around town but are marginal for spirited driving, there are better stuff out there that will let you keep the four lugs and haul it down from speed better than stock.
Once you get a little grease under you nails and tell someone you did the work you'll get it.
 

Davedacarpainter

Chicks can make things hard if they’re inspired...
SN Certified Technician
Nov 28, 2015
11,833
11,634
203
Discordia
Jan 22, 2017
#12
  • Jan 22, 2017
  • #12
Not mechanically inclined.......

You're starting into the modification bug. A year from now you'll be doing things to your car that you wouldn't believe you would ever have done.

Change out the clutch discs in your rear end. You'll wish you did otherwise. Our cars are to old, babied or not. The old clutches are going to start falling apart. It's not some magic to do these things, just read up on the subject. There must be a thousand youtube videos of people doing this exact thing.

Look at the positive side, you'll get some new tools! Plus you'll be proud of yourself when you do the repair.

I agree with karthief, 3.55's would be great. 3.73's aren't a bad choice, just a little annoying on a longer highway type drive.
 
Reactions: General karthief

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,134
10,752
213
polk county florida
Jan 22, 2017
#13
  • Jan 22, 2017
  • #13
And you will drive it long distance someday, and then more often, and farther, thinking well Detroit's not that far the Woodward dream cruise would be cool, mustang week, and suddenly your in Vagas living in that mustang because you lost at blackjack and your wife divorced ya and, wait, sorry, got a little off this morning.
Point is once you get started down this mechanical mayhem some call mustang life, very few return to stock life.
So put some wax on that hood, there's a bird just waiting to spot ya.
 
Reactions: DSB88GT
S

stang8384

Member
Jan 18, 2017
38
4
18
NY
Jan 22, 2017
#14
  • Jan 22, 2017
  • #14
If you are trying to say that upgrades are addicting then I definitely agree! 5 years ago, I'd be doing every upgrade possible! Family life has now given me serious time and some financial constraints!

I do have all the Haynes repair manuals and such but time is the major issue with trying to do the work myself. I've already done all the tune up stuff (plugs, wires, cap and rotor, ignition coil). I still need to change out the fuel filter and change the pcv valve. I had a hard time getting access to the pcv valve screen. So I gotta try to tackle that again.

As of now, I believe I have a oil pan gasket leak which I will most likely try to change out myself and a rear main seal leak which I was hoping to wait until I get the clutch replaced before I touch that. Is there a problem with that?!

I will keep it mainly stock. It's only driven during summer and I hope to pass it down to my boys.But as it is now, it is slow as heck! So I'd like to give it a little more pep.

What are the pros and cons of 3.55 vs 3.73s?
 
Last edited: Jan 22, 2017

Davedacarpainter

Chicks can make things hard if they’re inspired...
SN Certified Technician
Nov 28, 2015
11,833
11,634
203
Discordia
Jan 22, 2017
#15
  • Jan 22, 2017
  • #15
stang8384 said:
If you are trying to say that upgrades are addicting then I definitely agree! 5 years ago, I'd be doing every upgrade possible! Family life has now given me serious time and some financial constraints!

I do have all the Haynes repair manuals and such but time is the major issue with trying to do the work myself. I've already done all the tune up stuff (plugs, wires, cap and rotor, ignition coil). I still need to change out the fuel filter and change the pcv valve. I had a hard time getting access to the pcv valve screen. So I gotta try to tackle that again.

As of now, I believe I have a oil pan gasket leak which I will most likely try to change out myself and a rear main seal leak which I was hoping to wait until I get the clutch replaced before I touch that. Is there a problem with that?!

I will keep it mainly stock. It's only driven during summer and I hope to pass it down to my boys.But as it is now, it is slow as heck! So I'd like to give it a little more pep.

What are the pros and cons cons of 3.55 vs 3.73s?
Click to expand...
Clutch out is a perfect time to take care of the rear main seal.

Pros and cons. With 3.73's, first gear will seem useless almost. with 3.55's it will seem useless almost

If you like running through the gears fairly fast because of the enjoyment of it, then either is fine. 3.55's will just allow,the engine to spin a little slower at highway speeds. Little less drone from your exhaust (depending on the exhaust, of course).

Will you want to do much running at the dragstrip? If so, then you might even consider going a little higher numerically, like 4.10's.

Manual wise, the thing to do is go on ebay and look for a set of ford service manuals. I have a set for both my '83 and my '86. There's so much more detail there. I averaged right about $60 for each of them. Great resource.
 
Reactions: General karthief

FourEyed

Active Member
Jan 9, 2011
93
44
39
Jan 22, 2017
#16
  • Jan 22, 2017
  • #16
You might wanna start thinking about a good shifter too, Pro-5.0, Steeda Tri-Ax, etc. Because you will be doing twice as much shifting.

Than being said.. I'm running FRPP 3.73s in my 86 GT 5spd and I love every minute of it, makes me smile every time.
 
Reactions: Davedacarpainter

A5literMan

At least it is lumpy...
5 Year Member
Jul 30, 2011
4,674
2,343
194
Illinois
Jan 22, 2017
#17
  • Jan 22, 2017
  • #17
3.55's vs 3.73's debate is really splitting hairs imo. It's a very minimal difference at highway speeds(200rpms) and 1st gear usuage is darn near the same. I have had both and really like both gear sets. My present car I switched from 3.55 to 3.73 and the car performs better(but I have a cam etc and needed more gear). 55's are probably a better choice for a "nice day cruiser" and 73's if you want to maximize straight line performance. The op will probably like either.
 
Reactions: General karthief and Davedacarpainter
S

stang8384

Member
Jan 18, 2017
38
4
18
NY
Jan 22, 2017
#18
  • Jan 22, 2017
  • #18
FourEyed said:
You might wanna start thinking about a good shifter too, Pro-5.0, Steeda Tri-Ax, etc. Because you will be doing twice as much shifting.

Than being said.. I'm running FRPP 3.73s in my 86 GT 5spd and I love every minute of it, makes me smile every time.
Click to expand...

I picked up a mgw! And I after some of the comments, I was probably going to end up 3.55s.. But then I read the last sentence in your comment! I guess 3.73's it is!
 
Last edited: Jan 22, 2017
Reactions: A5literMan and Davedacarpainter
S

stang8384

Member
Jan 18, 2017
38
4
18
NY
Jan 22, 2017
#19
  • Jan 22, 2017
  • #19
And since I will have someone else installing them, how much more work is it to replace the clutch discs as someone recommended? Just curious how much more he may charge me
 
You must log in or register to reply here.

Similar threads

M
new member
  • markmoon
  • Jul 24, 2026
  • The Welcome Wagon
Replies
1
Views
147
The Welcome Wagon Jul 24, 2026
General karthief
Rear diff rebuild opinions
  • MrPerfect2
  • Oct 30, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
294
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 31, 2025
AeroCoupe
P
Air Fuel ratio bung location.
  • Praetorious
  • Feb 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
39
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 11, 2026
Noobz347
Paint and Body Frame rail dimensions
  • keel
  • Jan 30, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
25
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 13, 2026
keel
Rear end
  • RileyDymond
  • Feb 22, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 13, 2025
revhead347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?