good part's to get in the 13s

[1995 vibrantred]

I have a 1995 mustang Gt 5-speed, with 3.73 gears, exhaust, x-pipe, cold air. What is some good parts to get in low or mid 13s?

 

[DFG 5OH]

Definatly a good Heads/Intake/Cam Combo. Drag Radials, headers, you should see 13s.

 

[super302]

a good driver

i've seen minor bolt on cars (5spd) get well into 13's, mainly full exhaust, pulleys, gears, good tires, and a GREAT launch

 

[VibrantRedGT]

Got a 13.68 at 101MPH on this stuff.

Edelbrock Performer Intake
BBK 65MM Throttle Body
Pro-M 77MM MAF
Pulleys
MAC equal length headers
Bassani X pipe
MAC cat back
Aluminum driveshaft
Tri Ax shifter
Sticky tires

 

[super302]

Joe, was that with stock gears?

 

[WhiteDevil]

It ran 13.90 @99mph with 3.73s, Catback, CAI, and an Edelbrock Performer.

 

[rio95]

You should be pretty close. Check out my sig. If you do H/C/I you should be in the 12's in my opinion, not mid 13's.

 

[Darkhorse845]

Welcome Aboard!
A great driver is one!

 

[Killercanary]

Got a 13.68 at 101MPH on this stuff.

Edelbrock Performer Intake
BBK 65MM Throttle Body
Pro-M 77MM MAF
Pulleys
MAC equal length headers
Bassani X pipe
MAC cat back
Aluminum driveshaft
Tri Ax shifter
Sticky tires

With a VERY similar combo (edelbrock performer intake, 65mm t-body, pulleys, exhaust, 3.73's, nitto DR's) I ran a 13.83 at 98.55mph with a 1.91 60' in my 95 5 speed 'vert. Adding heads, cam, and fuel upgrades have gotten me to where I am now.

 

[1995 vibrantred]

I have not been to a drag strip yet.(because the close one is like 2hr away)
I am 16 years old so not a lot of money left after car payment, so a intake is to much right now. But what kind of pulles to get?

I am new but, rio95 what is H/C/I?

 

[DFG 5OH]

being 16 and wanting to have a fast car sucks!! i'm 17 and and just starting with some little stuff...hopefully i can get a better job, and make more money

 

[final5-0]

Driving like you don't care if you break it and REAL slicks will put you in the 13's as you are now. Most of us won't push our cars that hard for fear of breaking stuff.

Later
Grady

 

[Killercanary]

H/C/I stands for heads, cam, intake.

ASP pulleys are by far one of the best pulleys you can buy. I have the ASP aluminum pulleys on my car and it was one of the best mods I ever did to my car. They took me from a 14.96 at 91.5mph to a 14.6 at 94.89 with no other changes.

 

[super302]

another vote for ASP pulleys

 

[slvrbullit302]

nitrous nitrous nitrous

 

[urban96]

usuall boltons and intake

 

[VibrantRedGT]

Joe, was that with stock gears?

Oh yea 3:55's. Wish I had 4:10's.

 

[whiteyford0212]

here buddy this is your ticket

http://musclemustangfastfords.com/tech/0301_MMFFcatch22/

 

[Scott_95GT]

I have a 1995 mustang Gt 5-speed, with 3.73 gears, exhaust, x-pipe, cold air. What is some good parts to get in low or mid 13s?

If your car is in good tune (which I'm sure it is) your capable of high 13's right now. With some traction and a good launch, and maybee an intake manifold and some pullies, you are in the mid-13 sec. zone all day.

 

[wytstang]

Traction and a good driver will have you there. Pulleys are great and a short belt too.