Grind when letting clutch out after shift

Mustangsupra · Oct 21, 2006

Title says it all. There is a really bad grind when letting the clutch out after shifting. It also doesnt seem to want to go into fourth or fifth gear(maybe i am not used to short shifter). My friend thinks its the pressure plate(?). Once it is in gear it hauls ass with no slippage, but does kinda sound to me like something is rattling around in the tranny(maybe my imagination). If you let the clutch out real slowly it does not grind, but if you let the clutch out fast it grinds really badly.

any input would be great

thanks

jeremy

mo_dingo · Oct 22, 2006

Is it the transmission grinding or the clutch grinding? Will it grind if you cycle the clutch at idle?

I would suspect the TOB is busted and the release lever is grinding on the input shaft.

Mustangsupra · Oct 22, 2006

Sounds like its comming from the tranny maybe. You can feel the vibrations through the shifter, shifter actually shakes a lot (it popped out of gear once or twice). and what do you mean by "cycle the clutch"?

thanks

jeremy

urban96 · Oct 22, 2006

if you have it in neutral with the clutch engauged and rev it what happens?

Adam95GT · Oct 22, 2006

sounds like syncros to me... if so plan on a rebuild or new trans soon

Mustangsupra · Oct 22, 2006

I will try putting it in neutral with clutch engaged tommorow

thanks

for the input

jeremy

Mustangsupra · Oct 23, 2006

Nothing happens when its at idle and you rev it with clutch engaged or not. At idle it goes into all gears with no problems.

jeremy

Adam95GT · Oct 23, 2006

still sounds like syncros... do you have problems getting it in to gear some times.... ever miss shifts.... if it was a probe id say check the clutch fluid.... but we have cable clutches... soooo yeaaaah

Mustangsupra · Oct 24, 2006

i always thought that if the syncros were bad it would grind going into gear. This grinds after it is in gear and you are letting the clutch out. Maybe i am completely wrong, i dont know.

Anyone else think it is the throw out bearing?

Anyone think its the pressure plate?

thanks

jeremy

Adam95GT · Oct 24, 2006

well with my probe it wouldn't like to go in to gear... id miss 3rd at the track all the time... and here and there it would grind when i let off the clutch... then one day 3rd gear just decided it didnt want to be there any more... and i guess what ever broke off 3rd got stuck in my reverse because it would go in to reverse just move 5 feet and BANG!!!! and more another 5 feet and BANG!!!!! lol... limped it 70 miles with out 3rd... lots of fun... just dont want someone else stuck in the same situation... no im not to sure its just a sugestion...

Adam95GT · Oct 24, 2006

does it only do it when you really get on it and shift hard... mine grinds then 2... i think its the drive shaft torqueing up and scraping my e brake cable.... check your drive shaft....

Mustangsupra · Oct 24, 2006

nope, i could be going 2 mph shift into 2nd give it no gas at all and let out on the clutch and it grinds

thanks for the info though, i still dont know what to do...i was thinking about having the pressure plate and clutch replaced, but if it is the TOB or syncros......

jeremy

Adam95GT · Oct 24, 2006

clutch kits usually come with a new TOB

Black95GTS · Oct 24, 2006

Sounds like a dead ringer for the throw out bearing. By the way, I'd get this fixed ASAP.

Adam

Mustangsupra · Oct 24, 2006

car is not being driven, this unfortunatly is not the only problem i am having.....

so if i have the clutch and pressure plate replaced they will replace the TOB? (this is going to be done at pep boys, cheapest place in town, i think)

my buddy had pep boys do it to his fox with no problems, so hopefully they dont **** mine up......

Adam95GT · Oct 24, 2006

look over the write up... im gonna do mine my self i think... and id never go to pep boys for anything... dont have a reason... just dont trust the man or big companys for that matter...

Mustangsupra · Oct 24, 2006

i want this done quickly or else i would do it myself.....the major problem i see with taking it to pepboys is i dont know if it will get on the lift. It is about 2-3 inches off the ground.

jeremy

Adam95GT · Oct 24, 2006

it will all they have to do if anything at all, is pull up on the fenders... my probe was low as hell

Rains · Oct 24, 2006

Pep Boys! Yeah, clutch kits include, Throw Out Bearing, Clutch, and Pressure Plate... Pepboys also resurafaces the flywheel.... it that makes a difference

Otherwise, when the TOB broke in my 0ld 95, it was 10.00 @ Kragen

Hey- what ever happened to your previous SN, "Anti-Rains?"

BTW, we need to do the timing on that piece... actually do it, not just "guess" LOL

Mustangsupra · Oct 25, 2006

yeah because it runs like **** and wont idle with any accesories on....tommorrow i am going to flush the coolant and put that headgasket stuff in there, then change the spark plugs and oil.....

i was thinking about dropping the tranny....but i dont know

how long did it take you to do it abel?

jeremy

Grind when letting clutch out after shift

Mustangsupra

New Member

mo_dingo

Mustangsupra

New Member

urban96

bubb rubb says:"woo woooooo"

Adam95GT

New Member

Mustangsupra

New Member

Mustangsupra

New Member

Adam95GT

New Member

Mustangsupra

New Member

Adam95GT

New Member

Adam95GT

New Member

Mustangsupra

New Member

Adam95GT

New Member

Black95GTS

Active Member

Mustangsupra

New Member

Adam95GT

New Member

Mustangsupra

New Member

Adam95GT

New Member

Rains

Mustangsupra

New Member

Similar threads

Grind when letting clutch out after shift

New Member

New Member

bubb rubb says:"woo woooooo"

New Member

New Member

New Member

New Member

New Member

New Member

New Member

New Member

New Member

Active Member

New Member

New Member

New Member

New Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency