• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

Headlamp Removal

  • Thread starter Thread starter vvzer0incvv
  • Start date Start date Feb 27, 2004
V

vvzer0incvv

New Member
Aug 27, 2003
133
0
0
Carol Stream, IL
Feb 27, 2004
#1
  • Feb 27, 2004
  • #1
Hey guys i know that this is probably a stupid question but how can i remove the head lamps. I have the corners off i just can't get the headlamps off. Pics would be great, but anything will help. Thanks
 

krly79

Member
May 6, 2003
464
0
16
VA Beach & So Illinois
Feb 27, 2004
#2
  • Feb 27, 2004
  • #2
There are like long clip thingys on the top on the back and they pull up. I think there are like 2. I will take some pics in about 20 min or so when my wife gets back from tanning



EDIT: I just noticed that you have a 96. I'm not sure if they secure the same way, but I'll post some pics anyway.
 
V

vvzer0incvv

New Member
Aug 27, 2003
133
0
0
Carol Stream, IL
Feb 27, 2004
#3
  • Feb 27, 2004
  • #3
Thanks, your a life saver. There are some metal clips on the opposit side of the corner lamps but i have no idea how to get my hand in there to get at them.
 

krly79

Member
May 6, 2003
464
0
16
VA Beach & So Illinois
Feb 27, 2004
#4
  • Feb 27, 2004
  • #4











 
V

vvzer0incvv

New Member
Aug 27, 2003
133
0
0
Carol Stream, IL
Feb 27, 2004
#5
  • Feb 27, 2004
  • #5
WOW, thanks man! I'm working on the pass side and i got the half closest to the corner lamps out but the other side is stuck. I can't figure out how to pop that sucker out. The funnu thing is that there was only one clip on the bottom holding the lamp in. Thanks again for the picks.

BTW i saw that you fixed the slow dropping idle problem, how did you do it? Today i cleaned out the IAC and then i installed a copper cap with a 3/8 hole in it and that didn't do anything at all.
 

krly79

Member
May 6, 2003
464
0
16
VA Beach & So Illinois
Feb 27, 2004
#6
  • Feb 27, 2004
  • #6
Mine were pretty tight too. You can pull them out with some pliers or something. I put a copper cap with a 9/16 in hole, I think that is what it is. When it is cold, it drops alot quicker than when it is warm, but it is a little better.
 
You must log in or register to reply here.

Similar threads

P
Hello, core supports for '86 vs '90-3, i need some answers if anyone knows
  • Pony Dr.Mike
  • Mar 14, 2026
  • The Welcome Wagon
Replies
7
Views
318
The Welcome Wagon Mar 15, 2026
95steedamustang
R
Interior and Upholstery Interior roof adhesive removal HELP
  • Riley Barth
  • Jun 22, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
102
Fox 5.0 Mustang Tech Jun 23, 2026
Riley Barth
R
I
Removing NX NOS kit?
  • ironhorsewayne
  • Jun 7, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
83
1996 - 2004 SN95 Mustang -General/Talk- Jun 8, 2026
squeak93
R
Interior and Upholstery How to remove seatbelt torx screw
  • Riley Barth
  • Jul 6, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
20
Views
406
Fox 5.0 Mustang Tech Jul 13, 2026
Noobz347
C
98 gt fuel pressure issues
  • chasecollier1984
  • Jun 2, 2026
  • SN95 4.6L Mustang Tech
Replies
0
Views
93
SN95 4.6L Mustang Tech Jun 2, 2026
chasecollier1984
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?