• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Help! 5th Gear grinds...

  • Thread starter Thread starter sunil6784
  • Start date Start date Aug 23, 2005

sunil6784

Member
Mar 31, 2005
620
0
18
Boston, MA
Aug 23, 2005
#1
  • Aug 23, 2005
  • #1
Yesterday i changed my transmission fluid over to Mobil 1 Synthetic ATF. Today, I was getting on the highway and about 60 to 65 mph in 4th gear, i shifted to 5th. It grinded. It never used to do this before. I'm not sure what rpm i was running, but at the same speed, I shifted out of fifth and into neutral, then back into 5th, and it didn't grind. It seems it only happens when going from 4th to 5th. Please tell me I dont have to get a new tranny or rebuild this one. I hope its just something with the fluid. Any suggestions ??

EDIT: All other gears are fine, just 5th.
 

dkins419

New Member
Nov 14, 2004
187
0
0
Michigan
Aug 23, 2005
#2
  • Aug 23, 2005
  • #2
Sounds like 5th gear syncro is going out. The 5th gear syncros are only brass.
 

sunil6784

Member
Mar 31, 2005
620
0
18
Boston, MA
Aug 23, 2005
#3
  • Aug 23, 2005
  • #3
Also, I should have mentioned that it doesnt happen at low speeds, only like 60 and higher
 

J_Squared

Active Member
Jun 28, 2005
98
12
28
Buffalo, NY
Aug 23, 2005
#4
  • Aug 23, 2005
  • #4
yea def sounds like the synchro. at the lower speed the RPM difference is less so less likely to grind.
 

sunil6784

Member
Mar 31, 2005
620
0
18
Boston, MA
Aug 23, 2005
#5
  • Aug 23, 2005
  • #5
But why would this happen only after the fluid was changed, and why would it happen in 5th gear? isn't that very unlikely ?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Aug 23, 2005
#6
  • Aug 23, 2005
  • #6
5th gear has the softest synchro since it's made out of brass.

Good news is that it's easy to replace. You only need to pull the tailhousing of the trans. Some guys who are familiar with the t-5 can replace 5th without even pulling the trans out.

Try switching back to regular ATF. The synthetic is a bit more slippery so the the 5th gear synchro isn't grabbing as well and can't slow the gear down in time. Switching back to regular may add just enough friction to grab the gear and shift properly. It may take some time to work the syncthetic out though.
 

sunil6784

Member
Mar 31, 2005
620
0
18
Boston, MA
Aug 23, 2005
#7
  • Aug 23, 2005
  • #7
How do you go about getting a new synchro for it ?
 

Euphoric306

New Member
Apr 5, 2004
905
0
0
Aug 23, 2005
#8
  • Aug 23, 2005
  • #8
i would call up ddperformance in michigan (www.ddperformance.com), they sent me my rebuild kit

yea, no need to take apart the whole tranny so ur definitely in luck

if you would want to switch back to regular atf, you could try that but there is no guarantee and it will only prolong the need to replace that synchro

if you've got a lot of miles stocked up on your tranny, i would start thinking about a full rebuild, its a wonder to ur car hehe
 

sunil6784

Member
Mar 31, 2005
620
0
18
Boston, MA
Aug 23, 2005
#9
  • Aug 23, 2005
  • #9
Thanks for the replies! I've only got 70,000 miles on the odo, including body, motor and tranny. looks like I have a project for over the winter.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Aug 23, 2005
#10
  • Aug 23, 2005
  • #10
If you want to replace the 5th gear blocker, it's only a whopping $8.07 from Hanlon.

http://www.hanlonmotorsports.com/category.php


But while you have the trans open, you should perform a basic rebuild. It would be cheaper to do it now vs waiting til a main gear starts grinding badly and then you need to replace the gear and associated slider to the tune of $80 for each hard part.
 
You must log in or register to reply here.

Similar threads

T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
316
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
Drivetrain How much resistance, if any at all, is normal on a new 1st gear and synchro on a WC T5 transmission?
  • sleep-e
  • Jan 21, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
342
Fox 5.0 Mustang Tech Jan 22, 2026
sleep-e
Drivetrain 83’ Glx convertible C5 Trans help!
  • JacksonJared2113
  • Dec 25, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
530
Fox 5.0 Mustang Tech Dec 26, 2025
JacksonJared2113
L
Car has been overheating. Not sure what is causing it. Any help would be appreciated.
  • Luckysgirl
  • Jun 2, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
246
1996 - 2004 SN95 Mustang -General/Talk- Jun 2, 2026
Luckysgirl
L
P
Drivetrain Where to buy T5 synchros only, don't need full rebuild kit
  • pindude80
  • May 8, 2024
  • Fox 5.0 Mustang Tech
Replies
7
Views
3K
Fox 5.0 Mustang Tech May 25, 2024
Mustang5L5
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?