HELP! Ford racing Adjustable Clutch Cable

Realmongo

I prefer to be called "Evil Genius"
Founding Member
Oct 10, 2001
2,466
86
99
Western Mass
When the Ford Racing instructions say adjust to achieve 1/4" of play, does that mean 1/4" from the pedal being pulled all the way up until it encounters resistance when you push it down? If so, this results in one very high clutch pedal!

:shrug:
 
I have a FMS Adjustable cable. There should be NO slack in the cable and a fair preload. The TB is designed to ride on the clutch with 5-10 lbs of preload on the cable. This does not do any harm and keeps the cable form hopping off the quadrant when you let off the clutch pedal.

The binding common to adjustable cables is often due to misplacement of the adjusting nuts on the fork end of the cable. This will also cause the cable to wear and fray. Both nuts should be on the back side of the fork so that the domed nut faces the fork and the other nut serves as jam or locknut to the domed nut.

I like to have the clutch completely disengaged and still have about 1.5” travel left before the pedal hits the floor. If I shift only when the pedal hits the floor, there are several milliseconds that the clutch disk is not being driven by the engine or transmission. In theory, this lets the disk slow down some and makes less work for the synchronizers – keep in mind that this is a theory, but it seems reasonable. This means that I have only about 1” of free play at the top before the pedal starts to disengage the clutch. Keep in mind that these figures are all approximate.
 
I adjust it so that when you first push down on the pedal, it does not begin to get real firm for 1/4". This should be enough pressure to hold the TOB against the PP diaphram fingers, but not enough to actually deflect the fingers. On my car, with it like this, the clutch starts to engage a couple inches off the floor and finishes engaging a little more than halfway back up to the top.

Good luck.
 
Hmmm, JR and I disagree a little it seems. His way is text book, per the manual. I am a weenie when it comes to preloading the cable (fear of TOB failure).

I used to have a Ford adjustable cable with a single hook SVO quadrant, but now have a single hook UPR and OEM (non adjustable cable) and I kept the adjustment the same for both. Basically, i leave the adjustment loose and start it up. You can hear TOB noise in most cases. I tightened the slack out till the TOB noise went away. Then I fine tuned for my point of engagement and disengagement (I dont want the pedal to be buried to disengage, nor do I want to risk clutch slippage or premature wear on the diaphram fingers or TOB at the other end.

I would use JR's correct method - I posted how I do it (which seems to work). Were I to have a TOB getting noisy, I would dial in a little more preload.
I also think the term 'preload' thing is misleading, since you are preloading the cable before it starts cranking on the PP fingers (a lot of folks think that preload starts when the PP fingers start to compress. This is not so in my opinion and experience. I could be wrong).

Good luck.
 
I agree with hissin50, although I think him and JR have a lot of things in common with their way of doing it. Even though Hissin not realizing it by putting a little preload to get rid of the chirping TOB he is probably putting the right amount of preload. I had the same issue and changed from the adjustable cable to the stock OEM one with the firewall adjuster. WOrks fine. I found with the adjustable one it was much much harder to push the clutch down. Find which ever works for ya then stick with it
 
I agree with JR but have to dissagree with Jrichker about preload. I don't know about actuall preload, but it should be close. I was taught that it should be adjusted to the point where the TOB stopps spinning (no contact) but I don't know because most hydrolic and self adjusting cable assemblies sit it so the TOB is in contact. There shouldn't be actuall pressure though, just contact.

The point is that you don't want to ride the TOB, because they will fail. I did a clutch job on a 99 Mustang Faleen V6 (I know, it was a V6 with a salleen bodykit, cheapo body kit as well) 60K miles, TOB nearly locked up, flywheel glazed, pressure plate with some glazing as well. I did the same thing with riced out civic, hydlolic assembly, but the kit drove around with his foot on the clutch all the time. Both jobs were about a $1000 or so, maby they learned thier lessons. I had to take them out and teach them how to drive a stick shift. It's amazing how many people don't know how to properly drive a manual transmisison. Just because you can make it work doesn't mean your doing it right.
 
90mustangGT said:
I agree with JR but have to dissagree with Jrichker about preload. I don't know about actuall preload, but it should be close. I was taught that it should be adjusted to the point where the TOB stopps spinning (no contact) but I don't know because most hydrolic and self adjusting cable assemblies sit it so the TOB is in contact. There shouldn't be actuall pressure though, just contact.

The point is that you don't want to ride the TOB, because they will fail. I did a clutch job on a 99 Mustang Faleen V6 (I know, it was a V6 with a salleen bodykit, cheapo body kit as well) 60K miles, TOB nearly locked up, flywheel glazed, pressure plate with some glazing as well. I did the same thing with riced out civic, hydlolic assembly, but the kit drove around with his foot on the clutch all the time. Both jobs were about a $1000 or so, maby they learned thier lessons. I had to take them out and teach them how to drive a stick shift. It's amazing how many people don't know how to properly drive a manual transmisison. Just because you can make it work doesn't mean your doing it right.


JR is pretty mcuh quoting Ford. A lot of TOB for the 5.0 mustang chirp like a grasshopper and ford's answer was to put at most 10lbs of preload. so disagree if you will but it is suppose to ride on the TOB. I had the cirp and did a lot of searching to figure out why. That is the answer I was given 95% of the time.
 
Not to hijack the thread, but it seems multiple inputs coming to the same conclusion, so let's extend the question a bit.

I have a Steeda quadrant, firewall adjuster, and adjustable cable - all purchased together.

To me, it always feels like the clutch engages improperly a lot and I have played around with the cable a lot.

I have seen many people on the boards say to get everything I mentioned above with a stock Ford cable (non-adjustable). I am tempted to do this as I hate the way the adjustable cable feels.

My question is, if I were to go to a non-adjustable cable, is the adjustability still good with the firewall adjuster and the multiple latch positions on the quadrant?
 
criticman said:
My question is, if I were to go to a non-adjustable cable, is the adjustability still good with the firewall adjuster and the multiple latch positions on the quadrant?
As long as the cable and quadrant work together, it should be fine. For example, the SVO single hook has a huge, long throw, so the stock cable wont fit it - the adjustable Ford cable is required.

When I went from the Ford adjustable cable to the OEM style cable, there was a bit of a difference. Peeps say that the non-adjustable Ford cable is not as good a quality as the non-adjustable, but I tell ya what - it looked pretty decent to me. Not quite as good as the stocker, but pretty close. I have no experience with the Steeda stuff though.

And with this set up, I have plenty of adjustment.

In regard to earlier posts, I think TB is right. JR and I end up with a very similar adjustment. I think the difference is in what we define preload as (and that skewed interpretation would likely be mine). Simply said, I adjust it tight enough to shut up the TOB and that is about it (unless I need to get the POE off the floor).

Good luck.
 
Realmongo said:
I finshed putting it in. I left it at 1/4" from the top mechanical stop but as I said the pedal is pretty high. I am worried about wearing the TOB too.
You kinda lost me. Where is the point of engagement in relation to the floorboard? Can you feel a little bit of 'soft' pedal travel before you start loading the PP fingers?
 
HISSIN50 said:
You kinda lost me. Where is the point of engagement in relation to the floorboard? Can you feel a little bit of 'soft' pedal travel before you start loading the PP fingers?

Okay, if you take the clutch pedal and pull it up as far as it will go, then you have about 1/4" of downward movement before you hit resistance.
 
I called up Ford Racing, and this is what they told me to do:

1. have someone hold the clutch pedal all the way up against the mechanical stop.

2. Adjust all the play out of the cable.

3. Loosen the adjusting nut 1/4-1/2 Turn.

4. Tighten the jam nut.
 
Realmongo said:
I called up Ford Racing, and this is what they told me to do:

1. have someone hold the clutch pedal all the way up against the mechanical stop.

2. Adjust all the play out of the cable.

3. Loosen the adjusting nut 1/4-1/2 Turn.

4. Tighten the jam nut.

Sounds good to me. Way to go on calling the source.