• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

help with codes

  • Thread starter Thread starter ninety1gt
  • Start date Start date Jan 31, 2006

ninety1gt

New Member
Aug 27, 2005
162
0
0
san antonio
Jan 31, 2006
#1
  • Jan 31, 2006
  • #1
i pulled 96,85, and 66, some tell me what they mean?
 

Beasly B

New Member
Jan 7, 2006
165
0
0
Virginia
Jan 31, 2006
#2
  • Jan 31, 2006
  • #2
code 96 is fuel pump secondary circuit failure, is and the problem is fuel pump secondary circuit is bad or fuel pump relay is bad.85 is CANP solenoid circuit failure, problem, CANP solenoid is bad or circuit is bad. 66 is MAF sensor out of range (signal voltage too low), problem MAF sensor is bad or not calibrated correctly. That's the info that I have on it Hope it can help you
 

ninety1gt

New Member
Aug 27, 2005
162
0
0
san antonio
Jan 31, 2006
#3
  • Jan 31, 2006
  • #3
Beasly B said:
code 96 is fuel pump secondary circuit failure, is and the problem is fuel pump secondary circuit is bad or fuel pump relay is bad.85 is CANP solenoid circuit failure, problem, CANP solenoid is bad or circuit is bad. 66 is MAF sensor out of range (signal voltage too low), problem MAF sensor is bad or not calibrated correctly. That's the info that I have on it Hope it can help you
Click to expand...



so its probably the fuel pump relay if the car surges and dies at a stop??


i think the maf is wrong because my mechanic unhooked the plug to the sensor for a little bit
 

Beasly B

New Member
Jan 7, 2006
165
0
0
Virginia
Jan 31, 2006
#4
  • Jan 31, 2006
  • #4
yea I'd probably start there and see what happens
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jan 31, 2006
#5
  • Jan 31, 2006
  • #5
ninety1gt said:
i pulled 96,85, and 66, some tell me what they mean?
Click to expand...
Code 66 MAF below minimum test voltage.
Insufficient or no voltage from MAF. Dirty MAF element, bad MAF, bad MAF wiring, missing power to MAF. Check for missing +12 volts on this circuit. Check the two links for a wiring diagram to help you find the red wire for computer power relay switched +12 volts. Check for 12 volts between the red and black wires on the MAF heater (usually pins A & B). while the connector is plugged into the MAF. This may require the use of a couple of safety pins to probe the MAF connector from the back side of it.

There are three parts in a MAF: the heater, the sensor element and the amplifier. The heater heats the MAF sensor element causing the resistance to increase. The amplifier buffers the MAF output signal and has a resistor that is laser trimmed to provide an output range compatible with the computer's load tables.

The MAF element is secured by 2 screws & has 1 wiring connector. To clean the element, remove it from the MAF housing and spray it down with electronic parts cleaner or non-inflammable brake parts cleaner (same stuff in a bigger can and cheaper too).

The MAF output varies with RPM which causes the airflow to increase or decease. The increase of air across the MAF sensor element causes it to cool, allowing more voltage to pass and telling the computer to increase the fuel flow. A decrease in airflow causes the MAF sensor element to get warmer, decreasing the voltage and reducing the fuel flow. Measure the MAF output at pins C & D on the MAF connector (dark blue/orange and tan/light blue) or at pins 50 & 9 on the computer.

At idle = approximately .6 volt
20 MPH = approximately 1.10 volt
40 MPH = approximately 1.70 volt
60 MPH = approximately 2.10 volt

Check the resistance of the MAF signal wiring. Pin D on the MAF and pin 50 on the computer (dark blue/orange wire) should be less than 2 ohms. Pin C on the MAF and pin 9 on the computer (tan/light blue wire) should be less than 2 ohms.

There should be a minimum of 10K ohms between either pin C or D on the MAF and ground.

See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host)

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

To clean the MAF, remove the MAF element and gently spray it with electrical contact cleaner. You can also use non-flammable brake parts cleaner (same chemical in a bigger can & cheaper too). Let it dry and put it back in.

http://www.autozone.com/servlet/UiB..._us/0900823d/80/19/59/5a/0900823d8019595a.jsp

Code 85 - CANP solenoid - The Carbon Canister solenoid is inoperative. Check vacuum lines for leaks and cracks. Check electrical wiring for loose connections, damaged wiring and insulation. Check solenoid valve operation by grounding the gray/yellow wire to the solenoid and blowing through it.
The computer provides the ground for the solenoid. The red wire to the solenoid is always energized any time the ignition switch is in the run position.

Code 96 – KOEO- Fuel pump monitor circuit shows no power - Fuel pump relay or battery power feed was open - Power / Fuel Pump Circuits. The fuel pump circuit lost power at one time or another.

Look for a failing fuel pump relay, bad connections or broken wiring. The fuel pump relay is located under the Mass Air Meter on Fox bodied stangs built after 91. On earlier model cars is under the passenger seat. On Mass Air Conversions, the signal lead that tells the computer that the fuel pump has power may not have been wired correctly. See http://www.stangnet.com/tech/maf/massairconversion.html

To help troubleshoot the 96 code for 91-93 models see http://www.autozone.com/images/cds/gif/large/0900823d80195960.gif

Look for power at the fuel pump - the fuel pump has a connector at the rear of the car with a pink/black wire and a black wire that goes to the fuel pump. The pink/black wire should be hot when the test connector is jumpered to the test position. . To trick the fuel pump into running, find the ECC test connector and jump the connector in the lower RH corner to ground. http://www.mustangworks.com/articles/electronics/eec-iv_codes.html for a description of the test connector. it. No voltage when jumpered, check the fuel pump relay and fuse links.

Power feed: Look for 12 volts at the pink/black wire (power source for fuel pump relay). No voltage or low voltage, bad fuse link, bad wiring, or connections. Remember that on 92 or later models the fuel pump relay is located under the Mass Air meter. Watch out for the WOT A/C control relay on these cars, as it is located in the same place and can easily be mistaken for the fuel pump relay.

Relay: Turn on the key and jumper the ECC test connector as previously described. Look for 12 volts at the dark green\yellow wire (relay controlled power for the fuel pump). No voltage there means that the relay has failed, or there is a broken wire in the relay control circuit.
 

ninety1gt

New Member
Aug 27, 2005
162
0
0
san antonio
Jan 31, 2006
#6
  • Jan 31, 2006
  • #6
man wtfffff, i replaced fuel relay and nothing, 12.05 volts at maf, what else can be causing my surging and dieing??????????
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 1, 2006
#7
  • Feb 1, 2006
  • #7
See the sticky "Help me create the Surging Idle Checklist" at the top of the forum for help with your idle problems. The first post in the sticky has almost all the details you need.
 
You must log in or register to reply here.

Similar threads

H
97 cobra maf sensor help
  • Hopper1979
  • Oct 16, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
162
1996 - 2004 SN95 Mustang -General/Talk- Oct 17, 2026
CAMTWO1070
M
05 Mustang GT With Annoying P0463 Issue
  • Machbud
  • Oct 17, 2026
  • 2005 - 2009 Specific Tech
Replies
2
Views
192
2005 - 2009 Specific Tech Oct 24, 2026
manicmechanic007
Engine Code 41 again
  • Creomod
  • Jul 7, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
862
Fox 5.0 Mustang Tech Jul 11, 2026
Mcmahst
B
Help! Fox with idle issues
  • bbarton
  • Sep 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
306
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 12, 2026
AeroCoupe
Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
393
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?