help with rear axle....

P

perfectspace1

New Member

Nov 17, 2006

3

0

0

anaheim, ca

Nov 17, 2006

#1

• Nov 17, 2006

• #1

help with rear axle....

ok so i have a 2003 ford mustang v6 engine......it was hit by an excursion of all cars....and now the rear driver side is making some noise from the axle....some one told me it could be the bearings or the axle could be just a little tweked and need replacing....either way....i dont know how to do either of these things...if anyone could help me out with a step by step on changing out the rear axle or changing the bearings ....or could recomend a good website with some kind of walk through on the process i would appreciate it....THANKS A LOT TO ANYONE WHO REPLIES!!!!!!!

 

R

Robs96

Member

Aug 29, 2006

131

1

16

Nov 18, 2006

#2

• Nov 18, 2006

• #2

If you were hit by another vehicle, turn it in to insurance, if possible. What part of the car got hit?

 

P

perfectspace1

New Member

Nov 17, 2006

3

0

0

anaheim, ca

Nov 18, 2006

#3

• Nov 18, 2006

• #3

rear axle help

no it already went through insurance and everything.....it started a couple months after the body work was all done. so i am taking it into my own hands and going to attempt to fix it on my own. thanks though

 

R

Robs96

Member

Aug 29, 2006

131

1

16

Nov 18, 2006

#4

• Nov 18, 2006

• #4

What I was asking was, has the car been hit in the rear on the driver side or is this something that isn't collision related. The best way to go would be to get a Ford shop manual, or at least a Haynes which would outline the procedure. If it's axle replacement, you will need to disassemble alot of things.
Remove the rotor and caliper from the driver side
Remove the rear axle cover bolts and remove the cover
Remove the pinion lock bolt
Slide the pinion shaft out
Push in on the axle and remove any c-clips
Pull the axle out, just don't be careless doing it
It goes back together by reversing the steps
It probably wouldn't hurt to replace the axle seal as well since you will have gone this far. Pull it out and use a piece of wood or an oversized socket and tap it in. Hope all this helps you.

 

R

Robs96

Member

Aug 29, 2006

131

1

16

Nov 18, 2006

#5

• Nov 18, 2006

• #5

And of course, be sure to add the correct amount of fluid and some friction modifier when you put it all back together. To remove the axle bearing, find something to pull it out with and use a socket or wood to drive it back into position. Just make sure it is in all the way.

 

P

perfectspace1

New Member

Nov 17, 2006

3

0

0

anaheim, ca

Nov 18, 2006

#6

• Nov 18, 2006

• #6

thanks

it was hit on the driver side rear panel........the noise started a couple months after the accident...so i dont know if it caused it or not.....but regardless thanks for all your info...i will go pick up a book today...hopefully that helps me out.

 

R

Robs96

Member

Aug 29, 2006

131

1

16

Nov 19, 2006

#7

• Nov 19, 2006

• #7

Hope it works out okay.

 

R

Robs96

Member

Aug 29, 2006

131

1

16

Nov 19, 2006

#8

• Nov 19, 2006

• #8

Sounds like it probably was and body shops only fix the obvious...the bent and broken. If you have any questions then don't hesitate to ask.