• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum

Holy Crap!!!

  • Thread starter Thread starter Sharkster
  • Start date Start date Aug 7, 2005
S

Sharkster

New Member
Oct 25, 2004
127
0
0
Aug 7, 2005
#1
  • Aug 7, 2005
  • #1
Changed the oil, oil filter and air filter on the Cobra and headed down to the Kwik trip for some gas. Got about 10 blocks away and OMG I smell burning oil. I didnt spill any. Pull up to the pumps and get out and look back to see the oil stream behind my car going into the street. Look under and theres the puddle and oil sprayed everywhere under the car from the filter back on the drivers side. PANIC
Was gonna have it towed, nobody would come out on a Sunday night. I wasnt going to drive it back home and risk a sieze up. Couldnt leave it on the lot and had to take a chance. Bought 10 qts of 5w20 and away I went stopping and checking it every couple of blocks and adding if I needed it. Talked to a guy at the Kwik Trip in a 5.o that pulled up and told him I just changed the oil and I thought I blew a seal. He looked at the amount of oil and said i dont think so.... you got the filter in too tight and stipped a thread on it, just back it out easy when you change it.

Are you ready for this stupid mistake? I get home and the Wife says ok what did you screw up with an oil change. I said nada and showed her the old filter and said it had a good coat of oil on the seal and all. She says what and I show her the seal on the old filter. Holy **** the seal on the old filter is gone. OMG it was left stuck on there when I put the new filter on and I didnt see it. Do I feel like a dufus or what. Now I have a ****load of oil to clean up in the garage and driveway.

Anybody know If I can take the car wash spray gun and set it to soap and will it spray good enough to get all of the oil out from under the car???
 

COBRA90GT

Mustang Master
Sep 22, 2001
6,654
0
87
HOCKEYTOWN ® , MI
Aug 8, 2005
#2
  • Aug 8, 2005
  • #2
Eh, yeah you gotta be careful about the old gasket sticking to the oil filter housing - hindsight is 20/20 in your case.

You could probably remove most of it by spraying it off at a car wash, but I don't think you'll be able to get all of it off unless you take the time to do a thorough job and wipe it off with some old rags. Jack it up (using jackstands as well - safety first!) and spend some quality time underneath the engine bay.

Have fun.
 

sawman70

New Member
Nov 15, 2004
156
0
0
Cleveland Ohio Area
Aug 8, 2005
#3
  • Aug 8, 2005
  • #3
Get some Gunk Foamy Engine Bright on your way to the wash. Spray the Gunk and let it soak, then rinse.

If you have never used it, it is like magic.
 
U

Uncle Meat

Banned
Jun 13, 2002
0
1
0
Prattville, Alabama
Aug 8, 2005
#4
  • Aug 8, 2005
  • #4
Simple Green works well too. Spray it all down, let soak, rince off.

U.M.
 
S

Sharkster

New Member
Oct 25, 2004
127
0
0
Aug 8, 2005
#5
  • Aug 8, 2005
  • #5
I grabbed a bottle of the Simple green for engines the other day as I was going to be cleaning the dirt out of the engine bay. Engine bay area is ok except for the filter.... underneath is like, WOW
 
C

c_a_otoole

New Member
Jul 28, 2005
1
0
0
Colorado
Aug 8, 2005
#6
  • Aug 8, 2005
  • #6
Uncle Meat said:
Simple Green works well too. Spray it all down, let soak, rince off.

U.M.
Click to expand...


Simple Green is amazing stuff.....I work on ships and we use it for EVERYTHING.. we buy it in 55 galloon drums... after you get it up maybe try to get somthing like that miracle grow inductor thing you see at garden stors that allows you to use your hose and slowly add the simple green through there??? I don't think the simple green could hurt anyhting underneath.
 
S

Sharkster

New Member
Oct 25, 2004
127
0
0
Aug 9, 2005
#7
  • Aug 9, 2005
  • #7
Got the oil filter off last night and the new one on. The seal I forgot about looked like a pretzel. All is good there.
Wpied the underside down with paper towels as best I good and took it to the car wash. Srayed the hell out of it with simple green for engines and let it site for 10 minutes. Sprayed it with the engine and tire cleaner setting and the high pressure wash. Damn underside never looked so good.

All is good now
Thanks folks
 

JESTER

My dog and I are pee pals.
Founding Member
Dec 11, 1998
1,769
1
59
Newnan, GA
Aug 9, 2005
#8
  • Aug 9, 2005
  • #8
bad oil change story.

Back when I lived in an apartment - they really didn't like you doing work on your car in the driveway (had a garage with my appt)...so when I DID do maintenance, I tried to move as fast as possible.

Well, I was changing the oil on my old Cobra.
- Got the car jacked up and on stands
- Pull the baffle off the valve cover
- Got the oil pan out and slide it under the car(you know the one that holds like 5 gal that you can get from Wal-Mart - plug on top, drain spout on the one side so you can recycle it)
- Pull the drain plug out of the main sump of the oil pan....opps drop the plug...it's cool I'll pick it up later.
- Jump up and run in the appt to grab a drink
- Grab new oil filter and case of oil
- Come back to car

What I found was basically that the Exxon Valdese has spilled out from underneath my car.
I started thinking "that pan was NOT full" so I jump under the car and still my finger up against the drain plug hole (motor was still VERY, warm by the way)....
Come to find out...that drain plug that I figured I would get later...landed in the pan and plugged the drain hole...so the pan only held so much before it just drained everything else all over the place.

So, after ruining 3 towels a full roll of paper towels and a gallon of bleach, no one at the apartment complex ever knew a thing....
 
B

brianmef

20+ Year Stangneter
Nov 19, 2003
138
0
16
May 8, 2007
#9
  • May 8, 2007
  • #9
.
 
K

KobraKomander

New Member
Nov 16, 2003
63
0
0
May 9, 2007
#10
  • May 9, 2007
  • #10
brianmef said:
.
Click to expand...

Damn talk about digging up an old thread!
 
F

FKN Fast 03

New Member
Aug 8, 2007
0
0
0
Knoxville TN.
Aug 8, 2007
#11
  • Aug 8, 2007
  • #11
I bet that wont happen again.
 
You must log in or register to reply here.

Similar threads

C
Knocking after pull- went away?
  • Connormcclark
  • Oct 6, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
232
1996 - 2004 SN95 Mustang -General/Talk- Oct 6, 2025
gkomo
J
'04 3.8L V6 mineral deposits and oil on #3 cylinder. Does it need a rebuild or something simpler?
  • joeybuddy96
  • Mar 18, 2026
  • SN95 V6 Mustang Tech
Replies
7
Views
302
SN95 V6 Mustang Tech Jul 24, 2026
gkomo
B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
735
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
G
  • Poll Poll
I got a free Mustang from Grandma
  • GrannysMustang
  • Mar 4, 2026
  • The Welcome Wagon
Replies
14
Views
454
The Welcome Wagon Mar 6, 2026
Realmongo
Engine Gas in my oil
  • limp
  • Jun 15, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
35
Views
1K
Fox 5.0 Mustang Tech May 16, 2026
Mindseye007
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?