How Did You Mount Your Rear Seat Delete

Venom351R · Jul 30, 2008

Considering the Mustang is going to be down for awhile until I get the dyno tune done ( and my other new tire for the front to get here) I figured I would try and install the rear seat delete that I bought this past spring. Its the regular plywood w/ the black carpet over it. Any one have any pictures or a good description on how you mounted this in? I'm going to be pulling out the rear seat later today.

Mustangless · Jul 30, 2008

I have mine mostly finished, but the bottom part is not in good. I have the back of the bottom part with velcro on it. I was going to velcro the front part to the car's carpet, but the velcro does not stick to the carpet.

This might help you
1999-2004 Hardtop Mustangs Seat Delete- Installation Instructions at AmericanMuscle.com

Venom351R · Jul 30, 2008

There rear seat wont come out, the small tab on the drivers side that you have to push is is all f'ed up and no matter what I do the seat wont pop up. I got the passengers side out just fine but this one is impossible.

Venom351R · Jul 30, 2008

The only way this is going go come off is to unbolt the 2 screws that old down that plastic piece b/c there is no way its coming undone by pressing that button its seriously fubared. Im beyond pissed right now b/c you need about 4 hands to do this b/c you have to pry the seat up, shine a light to see the bolt and try and get the wrench on the bolt all of which is just about also impossible. This is the most easy step in this project and its become nothing but a cluster f ***. Plus the cage that is in the car is nothing but a hindrance that bar does nothing but get in the way and it hurts like hell to lay across it even when I lay blakets and stuff across it to pad it

Venom351R · Jul 30, 2008

Finally got it done, it was cake after I got the rear seat lower off that was a major PITA it should have never been that hard and the whole process would have take me an hr to do if it was not for that f'ed up release button and not taken all afternoon to do it. It came out good over all it did not mount in anyway it was form fit so you had to push it into place and it was a very tight fit. There is still some metal showing at the top of the back seat as you can see in the pic I may fix that at some point and put some black cloth there but for now I'm done screwing with it.

95BlueStallion · Jul 30, 2008

Looks like a good color match. I too had to remove the bolts to get my lower seat pad off. It wasnt fun, so Im right there with ya. I dont think your lower is gonna go anywhere with your cage in front of it. Is that the MM cage?

Venom351R · Jul 30, 2008

I believe its a Kenny Brown Street Cage.

Gearbanger 101 · Jul 30, 2008

Just curious, but what's the delete set up made out of? The stock seats (at least in my Cougar) weigh next to nothing. If the delete kit is mainly fiber board and carpet, I can't see someone experiencing very much in the line of additional weight savings?

Venom351R · Jul 30, 2008

Gearbanger 101 said:
Just curious, but what's the delete set up made out of? The stock seats (at least in my Cougar) weigh next to nothing. If the delete kit is mainly fiber board and carpet, I can't see someone experiencing very much in the line of additional weight savings?

I should have weighed the seats VS The kit. Its made of wood w/ thin carpet over it. It has some weight to it but I don't believe as much as the seats b/c the backs had the metal brace that went all the way around it. I went out and re adjusted the seat so the red metal no longer shows it just needed to be pushed up more, I took the bottom see off b/c I forgot to take the seat belts off from the rear.

Mustangless · Jul 30, 2008

How is your bottom part held in? My bottom part has a big gap in the middle where it does not go flat on the carpet. This is because on the outsides wires under the carpet raise it up.

Venom351R · Jul 31, 2008

Mustangless said:
How is your bottom part held in? My bottom part has a big gap in the middle where it does not go flat on the carpet. This is because on the outsides wires under the carpet raise it up.

Its all form fit, it just pushes into place. Its a very tight fit and needs a lot of persuasion to get it into place but IMO is better then having to bolt it up b/c it leaves no gaps b/c of the tight fit.

nmcgrawj · Jul 31, 2008

Did u try sticking a screw driver in the tab that u couldnt get?? Mine used to act up and i just used a flat head...

inphiniti · Aug 1, 2008

nmcgrawj said:
Did u try sticking a screw driver in the tab that u couldnt get?? Mine used to act up and i just used a flat head...

i gave him the suggestion of when in doubt, sludgehammer LOL

Venom351R · Aug 1, 2008

nmcgrawj said:
Did u try sticking a screw driver in the tab that u couldnt get?? Mine used to act up and i just used a flat head...

Yeah I did that it was not going at all, had to unscrew the base to get it to come off

inphiniti said:
i gave him the suggestion of when in doubt, sludgehammer LOL

How Did You Mount Your Rear Seat Delete

Venom351R

Mustangless

Member

Venom351R

Venom351R

Venom351R

95BlueStallion

My assy trans to myself

Venom351R

Gearbanger 101

Straight Outta Locash

Venom351R

Mustangless

Member

Venom351R

nmcgrawj

Advanced Member

inphiniti

Active Member

Venom351R

Similar threads

How Did You Mount Your Rear Seat Delete

Member

My assy trans to myself

Straight Outta Locash

Member

Advanced Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency