• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Huge disappointment...But expected.

  • Thread starter Thread starter SmittyFox5.0
  • Start date Start date Oct 10, 2005
S

SmittyFox5.0

New Member
Dec 2, 2002
32
0
0
Detroit, Michigan
Oct 10, 2005
#1
  • Oct 10, 2005
  • #1
This past Friday I took a vacation day from my job determined to get my project done to go racing on Saturday. I have been rebuilding my car for about 4 months and it was finally close enough that I could be finished with 1 good days work. Let me give the rundown of the stuff I did.

Custom 6 point cage
seats and harnesses
gauges/tach w/ custom mounts
Eliminate emission and HVAC systems
Rear Axle Rebuild (TracLoc & 3.73 gear)
Torque Box's & new Control Arms (Upper & Lower)
255LPH Fuel Pump
Rebuilt shortblock bored .030" with Forged Diamond Racing Pistons.
TFS stage 1 cam
TFS TW heads w/ 1.6 Roller Rockers
TFS Track Heat Intake
Edelbrock 70mm TB
C&L 76mm maf w/ trueflow pipe
30# injectors
Kirban AFPR
MSD 6A Ignition Box
Long tubes O/R H and Flowmaster Catback
+ Many other odds and ends to complete project

Well, just after dark hits I finish wiring in the ignition box and we are ready to fire it up. Well I don't let it Idle because of the new cam but I notice the car is running really rough and the throttle is super sensitive. About 5 minutes into its initial run, dad notices the headers are glowing read. Well it is running really lean. Run it a few more times and we are getting the same result. Kinda seems like it's sucking air somewhere because it will not stay running at idle. I have no clue where to start. Everything seems like it is in place and I can't seem to find where it could be sucking air from. Any ideas? I want to get this thing on the road so I can at least enjoy it for a little while before snow hits.
 

bluevenom867

I will have images of molesting stuffed animals in
Dec 15, 2003
1,704
1
0
St.Petersburg,FL
Oct 10, 2005
#2
  • Oct 10, 2005
  • #2
SmittyFox5.0 said:
dad notices the headers are glowing read. Well it is running really lean.
Click to expand...

Usualy that means it rich.

Check your timing and fuel pressure.

Be patient you'll figure it out.

 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Oct 10, 2005
#3
  • Oct 10, 2005
  • #3
Common area to have a huge vacuum leak is where the lower intake meets the heads. Your gasket could have shifted leaving the ports exposed.


I always thought it went like this:
Rich = blackish smoke out of the tailpipes and slow throttle response.

Lean = extra hot cylinder temperatures / exhaust (glowing red) Also, very sensitive throttle response.

When the car was running were both sides of the motor glowing red? Or just one side?
 
S

SmittyFox5.0

New Member
Dec 2, 2002
32
0
0
Detroit, Michigan
Oct 10, 2005
#4
  • Oct 10, 2005
  • #4
I am pretty sure it was just the passenger side that was glowing. I never saw it because I was in the car working the throttle. I was hoping that it was just the fuel pressure but I gotta believe it is sucking air.
 

bluevenom867

I will have images of molesting stuffed animals in
Dec 15, 2003
1,704
1
0
St.Petersburg,FL
Oct 10, 2005
#5
  • Oct 10, 2005
  • #5
srothfuss said:
Common area to have a huge vacuum leak is where the lower intake meets the heads. Your gasket could have shifted leaving the ports exposed.


I always thought it went like this:
Rich = blackish smoke out of the tailpipes and slow throttle response.

Lean = extra hot cylinder temperatures / exhaust (glowing red) Also, very sensitive throttle response.

When the car was running were both sides of the motor glowing red? Or just one side?
Click to expand...

The headers glow because fuel is still burning when the exhaust valve opens,causing some fuel to be burned in the headers,hence the glow.
 

Paul Perreca

New Member
Mar 30, 2005
1,085
0
0
Oct 10, 2005
#6
  • Oct 10, 2005
  • #6
srothfuss said:
Common area to have a huge vacuum leak is where the lower intake meets the heads. Your gasket could have shifted leaving the ports exposed.


I always thought it went like this:
Rich = blackish smoke out of the tailpipes and slow throttle response.

Lean = extra hot cylinder temperatures / exhaust (glowing red) Also, very sensitive throttle response.

When the car was running were both sides of the motor glowing red? Or just one side?
Click to expand...

My head gaskets stuck out a little tab for the lower intake gaskets to sit in, and that way they were stationary, Aren't all head gaskets like this? Mine are edelbrock i think 7113 head gaskets
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Oct 10, 2005
#7
  • Oct 10, 2005
  • #7
Paul Perreca said:
My head gaskets stuck out a little tab for the lower intake gaskets to sit in, and that way they were stationary, Aren't all head gaskets like this? Mine are edelbrock i think 7113 head gaskets
Click to expand...


Most gaskets have a tab to prevent slippage, but sometimes when you set the intake on the heads (dropping it into place so to speak) the gasket can slip down a little. This is what leads to vacuum leaks.

Since it's only happening on one side, I tend to think that is the side with the bad gasket.



Edit: spelling
 
M

mr.b

Founding Member
Aug 30, 2002
214
0
0
Oct 10, 2005
#8
  • Oct 10, 2005
  • #8
make sure timing isn't retarded a lot.
 

EMW150

Founding Member
May 22, 2000
2,020
1
46
Roaring Spring,PA
Oct 10, 2005
#9
  • Oct 10, 2005
  • #9
bluevenom867 said:
The headers glow because fuel is still burning when the exhaust valve opens,causing some fuel to be burned in the headers,hence the glow.
Click to expand...

That could be it if the timing is too retarded. They will burn in the header and exhaust temp will go up (which can lead you to think lean)
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Oct 10, 2005
#10
  • Oct 10, 2005
  • #10
Did you set the timing with a light once you got it cranked? The others pointing at retarded timing get my vote too. First thing to check.
Second - check for vacuum leaks --- EVERYWHERE. Be sure hoses are all hooked up or ports are blocked off (you eliminated a bunch of emissions stuff - did you cap off everything?) Re-snug your manifold bolts. Check tps voltage (.85V-1.1V from black to green wire) and that it smoothly ramps up to 4.5V-5.0V when you open the throttle (engine off please). Once that's all done - pull the diagnostic codes and see what it says.

MANY folks have problems with the calibration on the C&L meters - so you can also play with the meter by 'clocking' it to see if you get better running results. Take notes so you can get it back to where it was if your move makes things worse.

With all those mods, you didn't really think you'd fire it up the first time THE DAY before the race and be able to go racing did you?
 
B

blackice

New Member
Sep 23, 2005
17
0
0
CT
Oct 10, 2005
#11
  • Oct 10, 2005
  • #11
Easy enough to check for vacume leaks with a can of carb clean.
 
S

SmittyFox5.0

New Member
Dec 2, 2002
32
0
0
Detroit, Michigan
Oct 10, 2005
#12
  • Oct 10, 2005
  • #12
No, I really did not expect it to run perfect right away but I do admit it never really was a concern since I had so many other things to finish up before raceday. I am gonna go back through everything. I will pull the intake and rebuild everything just in case. I was going to check the rockers anyway so it isn't that big of a deal. One thing I didn't think of...I have the ford racing valve covers and I had to remove the oil baffle to clear the roller rockers. Well, the cast bosses where those screws thread into were touching the top of the lock nut for the rockers. Could this be causing a problem. I am gonna take care of it just to be safe.
 

v6v8swap

Member
Mar 20, 2004
113
0
16
Oklahoma
Oct 10, 2005
#13
  • Oct 10, 2005
  • #13
Our F-350 with a 460 in it did the same thing with the glowing exhaust manifolds on the initial run in after I put in a new long block. I found one vacuum port on the back of the lower manifold open (big vacuum leak) and the timing was badly retarded. You could have either one of these things or both as I did. Put a vac gauge on it and check the timing. I think that lean will burn hotter than rich, but that's just my guess.

Phil
 
You must log in or register to reply here.

Similar threads

K
Resolved Need some assistance. Holley Terminator X alongside H/C/I. Very rough/inconsistent idle
  • karhoot
  • Jun 6, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
236
Fox 5.0 Mustang Tech Jun 6, 2026
karhoot
K
S
Holley High-ram tuning settings
  • spencergt66
  • Apr 1, 2026
  • Digital Self-tuning Forum
  • 2
Replies
28
Views
1K
Digital Self-tuning Forum Jun 19, 2026
spencergt66
S
2
Running very very rich
  • 2esoteric
  • Oct 31, 2025
  • Fox 5.0 Mustang Tech
Replies
4
Views
469
Fox 5.0 Mustang Tech Oct 31, 2025
Noobz347
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
612
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
F
Ford 460 swap
  • Ford460
  • Sep 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
487
1996 - 2004 SN95 Mustang -General/Talk- Sep 14, 2026
Ford460
F
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?