• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

I drove my car tonight

  • Thread starter Thread starter revhead347
  • Start date Start date Jun 14, 2011
  • 1
  • 2
Next
1 of 2 Next Last

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,297
1,641
214
Acworth, GA
Jun 14, 2011
#1
  • Jun 14, 2011
  • #1
Finally, after 13 months of not running, I took my car around the block 3 times tonight. It chugs a little bit, and the oil pressure seemed a little on the low side. It's about 35psi at idle when the car is hot. It doesn't idle quite as nice as it did before either. Hopefully all that will be smoothed out with a tune. Also, the vacuum gauge stopped working. It's a little lower than it was before in the front, and it scrubs bad when I go over the bump down to the street. But yeah, it feels good to have a stang again. Off to emissions next week hopefully.

Kurt
 

Adam95GT

New Member
Aug 14, 2006
2,564
3
0
Burlington, NJ
Jun 14, 2011
#2
  • Jun 14, 2011
  • #2
Nice work
 

4Jenna

Founding Member
Sep 12, 2001
4,326
6
69
AZ
Jun 14, 2011
#3
  • Jun 14, 2011
  • #3
Good to hear man!!!

-Chris
 

95BlueStallion

My assy trans to myself
15 Year Member
Feb 22, 2007
5,126
3,091
214
Cedar Rapids, Iowa
Jun 14, 2011
#4
  • Jun 14, 2011
  • #4
Sounds good. If youre anything like me, you'll have the kinks worked out soon. I would almost rather not drive it, then have it running with issues. I like my baby to run like it should, without as much as an exhaust leak.
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,297
1,641
214
Acworth, GA
Jun 14, 2011
#5
  • Jun 14, 2011
  • #5
I think the first step is to get it clean. It's pretty nasty from sitting. Then unfortunately the first stop is emissions, then off to the alignment shop. Then I'll worry about crap like the vacuum gauge.

Kurt
 
3

302GTS

If you need herpes, I'm your man!
Apr 20, 2009
481
2
18
Largo, FL
Jun 15, 2011
#6
  • Jun 15, 2011
  • #6
Nice work man!
 

ProKiller

Founding Member
Apr 26, 2002
3,064
15
78
PA
Jun 15, 2011
#7
  • Jun 15, 2011
  • #7
at idle my oil pressure will go down to 25-30psi. but under any kind of load or rev it goes back and stays at 50
 

Pops Fun

10 Year Member
Feb 15, 2003
961
14
59
Cincinnati, Ohio
Jun 15, 2011
#8
  • Jun 15, 2011
  • #8
Enjoy....
 

1slow95

Founding Member
May 16, 2002
1,797
3
48
ohio
Jun 15, 2011
#9
  • Jun 15, 2011
  • #9
Always a good feeling to get the car back on the road again
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,297
1,641
214
Acworth, GA
Jun 15, 2011
#10
  • Jun 15, 2011
  • #10
ProKiller said:
at idle my oil pressure will go down to 25-30psi. but under any kind of load or rev it goes back and stays at 50
Click to expand...

Yeah, I have a high volume oil pump in this one. It actually goes right to 60 psi once it's over 1000 rpms. I just remember my old engine never going below 35 psi when it was new. This block has been modified to get more oil to the thrust bearing surface, so that might have something to do with it. It's not really bad or anything, but after spending 13 months and thousands of dollars getting this car running, I'm paranoid.

Kurt
 

toyman

10 Year Member
Jul 19, 2007
1,944
54
79
Vernon BC
Jun 15, 2011
#11
  • Jun 15, 2011
  • #11
Ford's spec for the oil pressure is 40-60 @ 2k rpm hot.
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,297
1,641
214
Acworth, GA
Jun 15, 2011
#12
  • Jun 15, 2011
  • #12
toyman said:
Ford's spec for the oil pressure is 40-60 @ 2k rpm hot.
Click to expand...

It's well over 40psi, not that I think Ford spec applies on a modified engine. I can't wait to get home and play with it. Nothing like driving it, then having to go to work for 3 days immediately. I'm going to mess with the timing and fuel a little bit. It's definately running way too rich. Got to get it leaned out to pass emissions on monday.

Kurt
 

Adam95GT

New Member
Aug 14, 2006
2,564
3
0
Burlington, NJ
Jun 16, 2011
#13
  • Jun 16, 2011
  • #13
revhead347 said:
Yeah, I have a high volume oil pump in this one. It actually goes right to 60 psi once it's over 1000 rpms. I just remember my old engine never going below 35 psi when it was new. This block has been modified to get more oil to the thrust bearing surface, so that might have something to do with it. It's not really bad or anything, but after spending 13 months and thousands of dollars getting this car running, I'm paranoid.

Kurt
Click to expand...

Your probably right, now there is less restriction your getting less pressure. I sit around 45 at idle.
 

Venom351R

Founding Member
Apr 27, 2002
4,548
41
98
MAINE
Jun 16, 2011
#14
  • Jun 16, 2011
  • #14
Damn Kurt I envy you, I cant wait until I can say " I drove my car today/Tonight/This morning"
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,297
1,641
214
Acworth, GA
Jun 17, 2011
#15
  • Jun 17, 2011
  • #15
Venom351R said:
Damn Kurt I envy you, I cant wait until I can say " I drove my car today/Tonight/This morning"
Click to expand...

Thanks for all the replies. I still have a long road ahead. I have to do the dreaded 500 brake in miles. 13 months is a long time to have a car down for me. With my rediculous work schedule, and almost 4 months of flooring it's understandable though.

Kurt
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,297
1,641
214
Acworth, GA
Jun 17, 2011
#16
  • Jun 17, 2011
  • #16
Ok, as requested, some video.

http://s114.photobucket.com/albums/...eous Videos/?action=view&current=DSCN0032.mp4

Yes, I did go out to the garage in red slippers. Not sure the exhaust clip is of much value, because the mic on this little camera is so overloaded.

Kurt
 

Adam95GT

New Member
Aug 14, 2006
2,564
3
0
Burlington, NJ
Jun 17, 2011
#17
  • Jun 17, 2011
  • #17
Thanks kurt, car sounds and looks good. You smelling lean or just no cats lol.
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,297
1,641
214
Acworth, GA
Jun 17, 2011
#18
  • Jun 17, 2011
  • #18
Adam95GT said:
Thanks kurt, car sounds and looks good. You smelling lean or just no cats lol.
Click to expand...

No cats and it's running pig rich. I have the chip on the richest setting. I'll set it back to lean and dial back the fuel pressure, throw on my ghetto cats, then take it to my redneck emissions guy and pray for the best.

Kurt
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jun 19, 2011
#19
  • Jun 19, 2011
  • #19
Oil Pressure is fine....When I do extensive mods to the oiling system idle is always a little lower depending on exactly what is done. The key is as soon as you touch the throttle it should increase immediately.

I tell all my customers 500 miles as well, truth be told as long as you seated the rings when you first started it...its ready to go UNLESS you have a clutch to break in as well.
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,297
1,641
214
Acworth, GA
Jun 19, 2011
#20
  • Jun 19, 2011
  • #20
Rick 91GT said:
Oil Pressure is fine....When I do extensive mods to the oiling system idle is always a little lower depending on exactly what is done. The key is as soon as you touch the throttle it should increase immediately.

I tell all my customers 500 miles as well, truth be told as long as you seated the rings when you first started it...its ready to go UNLESS you have a clutch to break in as well.
Click to expand...

Thanks for the reply Rick. The oil pressure jumps to 60psi the instant you hit the throttle, so I'm glad to have some re assurance there. The clutch was off the old engine. I had changed it not long before the transmission blew, so no break in there. What exactly do you mean by seat the rings? I changed the start up oil before I drove it. It had a little bit of black goo in it, which I assume is all the assembly lube and the ARP thread lubricant washing out.

Kurt
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

M
01 mustang 3.8 fuel pressure issue
  • Mhaley2006
  • May 29, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
135
1996 - 2004 SN95 Mustang -General/Talk- May 29, 2026
Mhaley2006
M
T
Help with a 95 5L crank no start
  • TheBubbaJoe
  • Nov 4, 2025
  • 1994 - 1995 Specific Tech
Replies
3
Views
446
1994 - 1995 Specific Tech Nov 5, 2025
AeroCoupe
B
More Issues With New Edge
  • Blackout67
  • May 3, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • 2
Replies
22
Views
761
1996 - 2004 SN95 Mustang -General/Talk- May 11, 2025
Blackout67
B
G
2006 Mustang GT o2 Sensor Wiring Issue Car Bogging/Choking
  • GCantero93
  • Sep 5, 2025
  • 2005 - 2009 Specific Tech
Replies
4
Views
984
2005 - 2009 Specific Tech Sep 6, 2025
Noobz347
S
Engine Stalls when downshifting/coasting
  • Scott_S
  • Nov 5, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
700
Fox 5.0 Mustang Tech Nov 6, 2025
Mustang5L5
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?