im screwed!! help me!

well its been a stressfull week. ive had no car because ive been putting on my sc. i get it on and it wont run. 2 days go by and i get it to run. go down to the dyno tuner and 2 hours a custom chip and $700 later im making 404ft/lbs of torque at the wheels at 4500rpm (cant rev any higher cause its too lean). he tells me i need a new maf (80mm pro-m) and 42# injectors plus an t-rex inline pump in addition to the 255lph pump i already have. i say ok, no big deal. i had to borrow the money from my mom cause im broke right now. so i owe her $700. now for the bad part. aparently when i put the car back together i cut the power wire to the radiator fan and didnt know it......oh ****. ran hot going to the tuner and on the way home but not that bad. get off the freeway and it gets bad. rushing to my g/f house so i could shut it down i blow a mother ph**king head gasket :bang: :bang: wow, that $2700 in the last week went real far <-----im being sarcastic if you couldnt tell. anyways, long story short, im broke and have a blown head gasket and pray i didnt bend a valve. white smoke pured from my car everywhere filling the street when it happened. the oil pan is full of coolant. pulled the dipstick and the fluid level was about 4-5" above the "full" line. coolant blew out my coolant overflow tank and went all over my msd box. i was able to drive it about a half block cause thats how far i was from her house when it happened. do you think i could have driven it if i had a bent valve? after it happened i thought i just smoked the tires or something but then when it began to sputter i got scared. anyways, i need a set of gaskets. i was thinking all metal like copper or aluminum (not sure which it is). what do you guys think? what thickness is stock? if you have a summit link that would be amazing cause i have to order these NOW!!!!! i dont want this to ever happen again so i want good ones.
im so ****ing stressed you have no idea
 
sounds like you have a nice setup going on . might want to look into a set of cometic head gaskets alot of poeple say they never blow. I dont know if thats good of bad . Just because ide rather blow my head gasket then fry my pistons or worse.
I say either get a realy nice set of cometics(thin metal type) from like benett racing or a set of felpros(paper type what i used).
Also ive heard pleant of people using regular felpro paper type gaskets who had none or little problems with them with the correct tune.
 
I think you need to keep stock style head gaskets on that car until you're sure the tune is dialed in and all is good to go. You put cometics, or copper, or something else on there that's stronger than stock then the next time something goes wrong it won't be the gaskets that give. Those kinds of gaskets aren't what you'd select for a "good enough" tune.

Edit: shtty beat me to it. :p
 
I agree with those guys, better to blow a head gasket than to fry a couple of pistons and what not. some say that head gaskets aren't suppose to blow so that is why they get the metal ones. I say it is a fail safe so something worse doesn't happen. Unless you are running some serious horse power or a race motor, then you would need the actual strength. Good luck, I hope all is for not in the end
 
ok thanks guys. im starting to think it was just me getting a little to throttle happy that blew it and not heat. i was running about 220* says my autometer. the tuner told me not to run past 4000rpm till i got 42# injectors but like an idiot i got excited and quickly forgot. im running felpro's now so ill probably get the same again.
on the plus side, the tuner said with 42# injectors and an 80mm pro-m he guaranteed me 425rwhp. not bad for running the stock cam.

what do you think about upgrading to head studs. i have arp head bolts but i was thinking of getting arp head studs, what do you think?
 
i was thinking about the cam although i really dont want to touch it just because of all the work of pulling the water pump and such off. i was also thinking 1.7's with stock cam. still not that great but better then it is now. should i replace both head gaskets or should i do a compression test and see which side blew? i think its the drivers side cause thats the side that had the most coolant drip out the tail pipe but thats not the best way to tell. im afraid of doing a compression test because of all that coolant that is in the oil pan. probably should just change both right? or should i test and see which side it is i have to replace?
 
i was thinking about the cam although i really dont want to touch it just because of all the work of pulling the water pump and such off. i was also thinking 1.7's with stock cam. still not that great but better then it is now. should i replace both head gaskets or should i do a compression test and see which side blew? i think its the drivers side cause thats the side that had the most coolant drip out the tail pipe but thats not the best way to tell. im afraid of doing a compression test because of all that coolant that is in the oil pan. probably should just change both right? or should i test and see which side it is i have to replace?

ive heard good and bad things about the e-cam for sc engines so im not sure which i want.....if i get one
 
luckythirteen13 said:
i was thinking about the cam although i really dont want to touch it just because of all the work of pulling the water pump and such off. i was also thinking 1.7's with stock cam. still not that great but better then it is now. should i replace both head gaskets or should i do a compression test and see which side blew? i think its the drivers side cause thats the side that had the most coolant drip out the tail pipe but thats not the best way to tell. im afraid of doing a compression test because of all that coolant that is in the oil pan. probably should just change both right? or should i test and see which side it is i have to replace?

our exhaust x and cross over so thats not a good way to tell. IDE do both head gasketsrealy no extra work. Also the water pump is nothing to take off belive me if you can do a head gasket youll have no problem doing the cam . youll allready have all the stuff unbolted from the head gasket install .
Fcam is is forced induction.. From what i heard f would be better than e for your aplication. I had a f and have no complaints buit nothing other than stock to compare it to.whAT ever you decide Good luck
 
Dont touch the cam if your as screwed as your saying. It doesnt sound like your in any type of position to change the cam, or even add rockers for that matter. Fix this first, and then move on, it will be easier to diagnose your problems this way (1 by 1).

Not only will it most likely ruin something else in your block (as others were saying) if you add a copper/metal/whatever gasket. It really is just a big bandaid to fix a problem that is still going to exist.
 
88GT17MA said:
Dont touch the cam if your as screwed as your saying. It doesnt sound like your in any type of position to change the cam, or even add rockers for that matter. Fix this first, and then move on, it will be easier to diagnose your problems this way (1 by 1).

Not only will it most likely ruin something else in your block (as others were saying) if you add a copper/metal/whatever gasket. It really is just a big bandaid to fix a problem that is still going to exist.

he blew a head gasket no bandaid just cure... he nows his air to fuel is messed ratio isnot right he needs a running car to fix this stuff so the tunner could finish his job. i sugested while he was down there throw the stock cam away its hurtting him bad in the power department
 
shttygtstang said:
he blew a head gasket no bandaid just cure... he nows his air to fuel is messed ratio isnot right he needs a running car to fix this stuff so the tunner could finish his job. i sugested while he was down there throw the stock cam away its hurtting him bad in the power department

Based on his post, it seems like hes more worried about money and getting the car driving than making more power.
 
well i ordered a new set of gaskets and arp head studs. i decided to wait on the cam for a couple reasons. i dont need another problem to diagnose right now and also, when i get another pump and injectors in the dyno tuner said id get at least 425rwhp. thats about as much as i want to run on the stock block so as much as id love to put in a cam and run maybe 450rwhp, i dont want to push it. i guess later today ill tear the motor down to the block and wait for the parts to come. i ordered the felpro gasket. you guys are right, id rather blow a head gasket every month then to blow my engine just once. the guy at summit helped me pick one out. he said it would be better for a sc motor. it has metal rings around the cylinders but its not the kind where i have to have the heads machined. they are just like the standard felpro but he said these are stronger but will still blow out long before the engine is damaged.
 
well good news, sort of. i decided to check the oil level again (this time now with the sun up) to see how bad it really is. i pulled the dipstick and found that the oil was perfect and there was no coolant in it at all. i was like "wtf" cause last night it was full of coolant. thats when i realized that last night (in the dark) i checked the trans fluid. hey, you blow a head gasket and see how straight your thinking. i was so relieved. my oil system is clean and working. i did a compression test. all cylinders are fine except the number 4. it made only 65psi on the test while all the others were normal (140's). so i have about 2/3 of the engine down. the passanger side valve cover is off, the intake is gone, sc is out, dizzy is out, electric fan, fuel rails,etc. ill pull the passenger side head tonight most likely but ill finish the tear down tomorrow. well i just wanted to post my good news (well as good as a blow head gasket can be), that i dont have coolant in the oil :nice: