Hi,
Last weekend I bought one JL Audio 12W3v2-D4 12 inch(300W, Dual 4 ohm) sub and a GM-7150M Pioneer Premier mono power amp( info: 500W x 1,4 ohm/800W x 1,2 ohm Max power; 250W x 1,4 ohm/360w x 1,2 ohm).
They recommend with going 23" x 14" x 10" box. This is the box size that I'm planning on going with but, I need to know if I'm going to need a capacitor. Once I built the box, how should I put the carpet on the box? Can I use a staple gun on it? Also what would be the best way to wire it to my stang?
Sorry, if these questions are stupid but this is an area that I have no knowledge on. If you need any more info just PM.
Thanks,
Max
Additional info:
***More info on the sub:
Nominal Diameter: 12 inches (300 mm)
Continuous Power Handling: 300 Watts
Voice Coil: 2.25" diameter, 4-layer, Kapton former
Available Configurations: Dual 2 ohm, Dual 4 ohm or Dual 6 ohm
Xmax (one-way, linear): 0.46"-0.51" (11.7-13.0 mm) depending on specific model
Sealed Enclosure Range: 1.00-1.50 cu.ft. (28.3-42.0 liters)
Ported Enclosure Range: 2.00-3.00 cu.ft. (57.0-85.0 liters)
VRCT Technology: YES
Elevated Frame Technology: YES
******************************
***More info on the amp:
2-Ohm Mono Stable
Variable Crossover (40-240Hz)
Selectable Bass Boost with Wired Bass Remote
Speaker Level Inputs
Peak Music Power: 800 Watts
Load Impedance Capability: 2~8 Ohm
Continuous Power (4 ohm): 250W x 1
Continuous Power (2 ohm): 360W x 1
Total Harmonic Distortion: 0.008%
Signal-to-Noise Ratio: 100dB
PWM Regulated MOSFET Power Supply
Screw-Type Speaker Terminals
Balanced Isolator Input Circuit
2 Channel RCA Inputs Gold
2 Channel Speaker Level Input
Input Level Control Hi-Volt (200mV ~ 6.5v)
Built-in Crossover Selectable LPF
Bass Level Control 50Hz, 0/6/9/12dB
Dimensions 12" x 2-3/8" x 12-3/4"
**************************
Last weekend I bought one JL Audio 12W3v2-D4 12 inch(300W, Dual 4 ohm) sub and a GM-7150M Pioneer Premier mono power amp( info: 500W x 1,4 ohm/800W x 1,2 ohm Max power; 250W x 1,4 ohm/360w x 1,2 ohm).
They recommend with going 23" x 14" x 10" box. This is the box size that I'm planning on going with but, I need to know if I'm going to need a capacitor. Once I built the box, how should I put the carpet on the box? Can I use a staple gun on it? Also what would be the best way to wire it to my stang?
Sorry, if these questions are stupid but this is an area that I have no knowledge on. If you need any more info just PM.
Thanks,
Max
Additional info:
***More info on the sub:
Nominal Diameter: 12 inches (300 mm)
Continuous Power Handling: 300 Watts
Voice Coil: 2.25" diameter, 4-layer, Kapton former
Available Configurations: Dual 2 ohm, Dual 4 ohm or Dual 6 ohm
Xmax (one-way, linear): 0.46"-0.51" (11.7-13.0 mm) depending on specific model
Sealed Enclosure Range: 1.00-1.50 cu.ft. (28.3-42.0 liters)
Ported Enclosure Range: 2.00-3.00 cu.ft. (57.0-85.0 liters)
VRCT Technology: YES
Elevated Frame Technology: YES
******************************
***More info on the amp:
2-Ohm Mono Stable
Variable Crossover (40-240Hz)
Selectable Bass Boost with Wired Bass Remote
Speaker Level Inputs
Peak Music Power: 800 Watts
Load Impedance Capability: 2~8 Ohm
Continuous Power (4 ohm): 250W x 1
Continuous Power (2 ohm): 360W x 1
Total Harmonic Distortion: 0.008%
Signal-to-Noise Ratio: 100dB
PWM Regulated MOSFET Power Supply
Screw-Type Speaker Terminals
Balanced Isolator Input Circuit
2 Channel RCA Inputs Gold
2 Channel Speaker Level Input
Input Level Control Hi-Volt (200mV ~ 6.5v)
Built-in Crossover Selectable LPF
Bass Level Control 50Hz, 0/6/9/12dB
Dimensions 12" x 2-3/8" x 12-3/4"
**************************